1. پراڊڪٽ ختمview
The Eberle KLR-E 7010 is a bimetal thermostat designed for controlling fancoil units. It provides precise temperature regulation and offers control over fan speed and operating mode (heating or cooling). This manual provides essential information for the safe and efficient installation, operation, and maintenance of your thermostat.
شڪل 1: سامهون view of the Eberle KLR-E 7010 Fancoil Thermostat. The image displays the front panel of the thermostat, which is white with the 'EBERLE' brand name in the top left. On the right side, there is a large rotary dial for temperature setting, marked in degrees Celsius from 5 to 30. An arrow indicates the current setpoint. On the left, there are two horizontal slide switches. The top switch controls the fan speed, with icons representing different fan speeds. The bottom switch selects between heating (wavy lines), off (center), and cooling (snowflake) modes.
2. اھم حفاظتي ھدايتون
- Always disconnect power to the fancoil unit and thermostat at the main circuit breaker before performing any installation, wiring, or maintenance.
- تنصيب ۽ وائرنگ سڀني مقامي ۽ قومي اليڪٽريڪل ڪوڊن جي مطابق هڪ قابل اليڪٽريشن طرفان ڪئي وڃي.
- Do not operate the thermostat with wet hands or when standing on a wet surface.
- پڪ ڪريو ته سڀئي وائرنگ ڪنيڪشن محفوظ ۽ صحيح طرح سان موصل آهن ته جيئن بجلي جي خطرن کي روڪي سگهجي.
- This device is designed for indoor use only. Do not expose it to moisture, extreme temperatures, or direct sunlight.
- Keep the thermostat away from children and pets.
3. انسٽاليشن گائيڊ
3.1. پيڪيج مواد
انسٽاليشن شروع ڪرڻ کان اڳ پڪ ڪريو ته سڀئي جزا موجود آهن:
- Eberle KLR-E 7010 Fancoil Thermostat unit
- Mounting screws (typically included with the unit)
- ھدايت وارو دستور (ھي دستاويز)
3.2. چڙهڻ جي هدايت
- جڳھ چونڊيو: Choose an interior wall location, approximately 1.5 meters (5 feet) above the floor, away from direct sunlight, drafts, heat sources, or areas with poor air circulation.
- بجلي بند ڪريو: Turn off the power to the fancoil unit at the main circuit breaker. Verify that power is off using a voltagاي جاچ ڪندڙ.
- Separate Base Plate: ٿرموسٽٽ جي اڳئين ڍڪ کي ان جي بيس پليٽ کان احتياط سان الڳ ڪريو.
- ماؤنٽ بيس پليٽ: Position the base plate on the wall and mark the drilling locations. Drill holes and insert wall anchors if necessary. Secure the base plate to the wall using the provided mounting screws.
- وائرنگ: Refer to the wiring diagram (Section 3.3) and connect the electrical wires to the appropriate terminals on the base plate. Ensure all connections are tight and correct.
- Attach Front Cover: Once wiring is complete and verified, carefully reattach the front cover to the base plate, ensuring it clicks securely into place.
- پاور بحال ڪريو: مکيه سرڪٽ برڪر تي بجلي کي واپس ڦيرايو.
3.3. وائرنگ ڊاگرام
The Eberle KLR-E 7010 thermostat is designed for 230 Volts systems. Due to variations in fancoil unit configurations and local electrical codes, a generic wiring diagram cannot be provided here. It is imperative that a qualified electrician performs all wiring to ensure proper functionality and safety. The electrician should consult the specific wiring instructions provided with your fancoil unit and the terminal markings on the thermostat's base plate.
4. آپريٽنگ هدايتون
4.1. ڪنٽرول مٿانview
The thermostat features three primary controls:
- درجه حرارت ڊائل: A large rotary dial on the right side of the unit, marked in degrees Celsius, used to set the desired room temperature.
- Fan Speed Switch: A horizontal slide switch on the upper left, typically with three fan blade icons, allowing selection of low, medium, or high fan speed.
- Mode Selection Switch: A horizontal slide switch on the lower left, used to select between heating (wavy lines), cooling (snowflake), or off (center) modes.
4.2. درجه حرارت کي ترتيب ڏيڻ
To set the desired room temperature, rotate the large dial clockwise or counter-clockwise until the indicator arrow points to your preferred temperature in degrees Celsius. The thermostat will then work to maintain this temperature.
4.3. فين اسپيڊ ڪنٽرول
Use the upper left slide switch to adjust the fancoil's fan speed:
- گھٽ: For quiet operation and minimal air circulation.
- وچولي: A balanced setting for general comfort.
- اعلي: For rapid temperature change or maximum air circulation.
4.4. Mode Selection (Heating/Cooling)
Use the lower left slide switch to select the operating mode:
- Heating (wavy lines): The thermostat will activate the heating function when the room temperature falls below the setpoint.
- بند (مرڪزي پوزيشن): The fancoil unit will remain off, regardless of temperature.
- Cooling (snowflake): The thermostat will activate the cooling function when the room temperature rises above the setpoint.
5. سار سنڀال
The Eberle KLR-E 7010 thermostat requires minimal maintenance.
- صفائي: Periodically wipe the exterior of the thermostat with a soft, dry cloth to remove dust. Do not use abrasive cleaners, solvents, or spray directly onto the unit.
- ڪوبه استعمال ڪندڙ-خدمت وارو حصو: The thermostat contains no user-serviceable parts. Do not attempt to open or repair the unit yourself. Refer all servicing to qualified personnel.
6. مسئلا حل ڪرڻ
If you experience issues with your Eberle KLR-E 7010 thermostat, consult the table below for common problems and potential solutions.
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| Thermostat not responding / No power | No power at the circuit breaker; Loose wiring connection. | Check the circuit breaker and ensure it is in the 'ON' position. Verify all wiring connections are secure (consult a qualified electrician). |
| Fancoil not heating/cooling | Incorrect mode selected; Temperature setpoint too high/low; Fancoil unit malfunction. | Ensure the mode switch is set to 'Heating' or 'Cooling' as desired. Adjust the temperature setpoint appropriately. Check the fancoil unit for operational issues. |
| فين ڪم نٿو ڪري | Fan speed switch set to 'Off' (if applicable); Fancoil unit fan malfunction. | Ensure the fan speed switch is set to a desired speed (Low, Medium, or High). Check the fancoil unit's fan for issues. |
| غلط درجه حرارت پڙهڻ | Thermostat located near heat/cold source or draft. | Relocate the thermostat to a more suitable position if possible, away from direct influences. |
If the problem persists after attempting these solutions, contact a qualified technician or customer support.
7. ٽيڪنيڪل وضاحتون
- برانڊ: Eberle
- ماڊل: KLR-E 7010
- قسم: Bimetal Fancoil Thermostat
- جلدtage: 230 وولٽ
- طول و عرض (L x W x H): 11.71 x 7.11 x 2.69 سينٽي ميٽر (تقريبن 4.61 x 2.80 x 1.06 انچ)
- وزن: 120 گرام (تقريبن 0.26 پائونڊ)
- فين ڪنٽرول: 3-speed fan selector
- موڊ ڪنٽرول: Heating/Cooling/Off selector
- درجه حرارت جي حد: عام طور تي 5°C کان 30°C (41°F کان 86°F)
- بيٽريون: Not required, not included
- ٺاهيندڙ حوالو: 3024146
- Article Model Number: 8402414979620
8. وارنٽي ڄاڻ
This Eberle KLR-E 7010 thermostat is covered by the manufacturer's standard warranty. The specific terms and duration of the warranty may vary by region and retailer. Please retain your proof of purchase for warranty claims. For detailed warranty information, refer to the documentation provided at the time of purchase or contact your retailer.
9. ڪسٽمر سپورٽ
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the retailer from whom you purchased the product or visit the official Eberle website for support contact information. When contacting support, please have your product model (KLR-E 7010) and proof of purchase readily available.