ھدايت وارو دستور

1. تعارف

This manual provides detailed instructions for the installation, setup, and operation of your Scimagic-RC Tuya WiFi 433MHZ Receiver, 1527 Remote Control, and Wireless Numeric Keypad. This system is designed to provide secure and convenient access control for automatic garage doors, swing gates, and sliding gate openers, integrating with smart home platforms like Tuya, Smart Life, Google Assistant, and Amazon Alexa.

2. حفاظت جي ڄاڻ

• Ensure all power is disconnected before performing any wiring or installation procedures.
• Installation should be performed by qualified personnel if you are unsure about electrical connections.
• ڊوائيس کي پاڻي ۽ انتهائي گرمي کان پري رکو.
• Do not attempt to repair the device yourself; contact support for assistance.
• This device is intended for use with automatic door/gate systems only.

3. پيڪيج مواد

Depending on your purchase, your package may include:

• وائرليس عددي ڪي پيڊ
• 433MHZ Receiver
• 433MHZ Remote Control (may be sold separately or in combinations)
• ماؤنٽنگ هارڊويئر (اسڪرو، وال اينڪر)

4. وضاحتون

4.1. Wireless Numeric Keypad

طاقت	6V DC (2x CR2032 Li battery)
بيٽري جي زندگي	Approx. 2 years (based on 4 operations/day)
تعدد	433.92MHz +/- 75KHz
ٽرانسميٽر پاور	1 ميگاواٽ
ڊيٽا فارميٽ	معياري
آپريٽنگ جي درجه حرارت	-20°C کان +55°C
Password Number	0-8 عدد
پنروڪ سطح	IP54
طول و عرض	85 x 75 x 35 ملي ميٽر
وزن	150 جي

4.2. 433MHZ Receiver

بجلي جي فراهمي	12V-24V ڊي سي
تعدد	433.92 ميگاز
ڪوڊس	Fixed/Learning/Rolling codes compatible
چينل	2 چينل
آپريٽنگ جي درجه حرارت	-40°C کان +80°C
استقبال واري حد	10-50m (Built-in Aerial antenna)

4.3. 433MHZ Remote Control

مواد	پلاسٽڪ + ڌاتو
آپريٽنگ فريڪئنسي	433.92MHz
استعمال	For 433Mhz RF receiver 1527 decode
مطابقت	Supports learning code (1527) receivers only. Not a clone remote.

5. سيٽ اپ

5.1. Keypad Battery Installation

The keypad requires two CR2032 Li batteries. To install or replace them:

1. Locate the battery compartment on the rear of the keypad.
2. Open the battery rear cover.
3. Insert two CR2032 batteries, ensuring correct polarity.
4. Close the battery rear cover securely.

5.2. رسيور وائرنگ

Connect the receiver to your automatic door/gate opener system according to the following terminal definitions:

• ANT: وصول ڪندڙ اينٽينا
• CH1: رلي آئوٽ 1
• CH2: رلي آئوٽ 2
• V+: جلدtage + (12V-24V DC power supply)
• جي ڊي: زمين

5.3. Pairing Remote Control with Receiver

To program a new remote control to operate your garage door or gate:

1. Press and release the yellow round button on the opener (or the 'LEARN' button on the receiver board). The learn indicator light (blue LED) will glow steadily for approximately 30 seconds.
2. Within these 30 seconds, press and hold the desired button on the hand-held remote that you wish to use to operate your garage door/gate.
3. Release the button on the remote when the opener light blinks once, or the blue LED on the receiver goes out. The new remote is now programmed.

5.4. Pairing Keypad with Receiver

To program the wireless numeric keypad with the receiver:

1. Long press the 'LEARN' button on the receiver board until the blue LED lights up.
2. On the keypad, enter the original password (e.g., '11' for left channel or '22' for right channel, as indicated in the video demonstration).
3. The blue LED on the receiver will go out, indicating a successful match.

Note: Refer to the video demonstration for a visual guide on the pairing process.

6. آپريٽنگ هدايتون

6.1. ريموٽ ڪنٽرول استعمال ڪندي

Once paired, press the programmed button on your remote control to activate the connected garage door or gate opener.

6.2. Using the Wireless Numeric Keypad

To operate the connected device using the keypad:

1. Enter your programmed password on the keypad.
2. Press the appropriate channel button (e.g., 'left arrow' or 'right arrow' depending on the channel programmed) to activate the opener.

The keypad is a dual-channel transmitter, meaning it can control two separate devices or functions with different combinations.

7. سار سنڀال

7.1. Keypad Battery Replacement

If the keypad's performance degrades or it stops responding, the CR2032 batteries may need replacement. Follow the steps in Section 5.1 for battery installation.

7.2. صفائي

نرم، سڪل ڪپڙي سان ڊوائيسز کي صاف ڪريو. رگڙيندڙ صاف ڪندڙ يا محلول استعمال نه ڪريو.

8. مسئلا حل ڪرڻ

• ڊوائيس جواب نه ڏئي رهيو آهي: Check battery levels in the keypad/remote. Ensure the receiver is powered correctly. Re-attempt the pairing process.
• محدود حد: Ensure the receiver's antenna is unobstructed. Check for sources of interference (e.g., other wireless devices, metal structures).
• جوڙڻ جي ناڪامي: Ensure you are following the pairing steps precisely. The timing for pressing buttons during the learning phase is crucial.

9. استعمال ڪندڙ ٽوٽڪا

• For optimal performance, ensure the keypad is mounted in a location with good line-of-sight to the receiver, especially for outdoor installations.
• The keypad is suitable for 95% of garage door openers worldwide.
• The keypad's estimated transmission range is 200m in open space and 35m indoors.
• The system is compatible with various smart home platforms, including Tuya, Smart Life, Google Assistant, and Amazon Alexa, allowing for integrated control.
• The keypad is designed for utmost security, with transmitted codes changing at each session.
• This system is compatible with Nice OXI poa1 portals.

10. وارنٽي ۽ سپورٽ

All products come with a 1-year warranty from the store. For technical support or warranty claims, please contact the seller directly. Ensure you retain your purchase receipt as proof of purchase.

For additional information, you may refer to the يوزر مينوئل (PDF).

11. سرٽيفڪيشن

This product is certified with:

• CE
• RoHS