ھدايت وارو دستور

1. تعارف ۽ اوورview

This manual provides essential information for the proper installation, operation, and maintenance of your new magnetic build platform for the Easythreed K10 3D printer. This product is designed to offer a reliable and convenient printing surface, enhancing your 3D printing experience. The package includes three individual platforms, each featuring a magnetic base and a textured mesh-hole surface for optimal print adhesion.

2. وضاحتون

3. سيٽ اپ ۽ تنصيب

Follow these steps to install your new magnetic build platform:

1. پرنٽر بيڊ تيار ڪريو: Ensure your Easythreed K10 3D printer is turned off and cooled down. Carefully remove any existing build surface or adhesive from the printer's heated bed. Clean the heated bed thoroughly with isopropyl alcohol to remove any dust, grease, or residue.
2. Apply the Magnetic Base (if applicable): If your printer bed does not already have a magnetic base, you may need to apply one (not included with this product, as this product is the top magnetic sheet). Ensure it is applied smoothly and without air bubbles.
3. بلڊ پليٽ فارم رکو: Align the magnetic build platform with the corners of your printer's heated bed. The platform is designed to fit precisely. Gently place it onto the magnetic base, ensuring it lies flat and is securely attached. The magnetic attraction will hold it in place.
4. ترتيب جي تصديق ڪريو: Double-check that the platform is centered and fully seated on the printer bed.
5. Perform Bed Leveling: After installation, it is crucial to perform a bed leveling procedure on your 3D printer. Refer to your Easythreed K10 printer manual for specific instructions on how to level the print bed. Proper leveling is essential for successful first layer adhesion.

4. آپريٽنگ هدايتون

The magnetic build platform is a passive component that provides the surface for your 3D prints. Proper operation primarily involves preparing the surface before printing and carefully removing prints afterward.

• ڇپائي کان اڳ: Ensure the platform surface is clean and free of debris. For some materials, a thin layer of adhesive (e.g., glue stick, hairspray) may be applied to further enhance adhesion, though the textured surface is designed to provide good adhesion on its own.
• ڇپائي دوران: Monitor the first layer of your print. If adhesion issues occur, re-check bed leveling and print settings (e.g., bed temperature, first layer speed).
• After Printing: Allow the print and the platform to cool down. Once cooled, the magnetic platform can often be gently flexed to release the print. Avoid using excessive force or sharp tools that could damage the surface.

5. سار سنڀال

Regular maintenance will prolong the life of your build platform and ensure consistent print quality.

• صفائي: After each print, or as needed, clean the surface with isopropyl alcohol (IPA) and a clean cloth. This removes any residual plastic or oils that can hinder adhesion.
• چڪاس: Periodically inspect the surface for any signs of wear, deep scratches, or damage. While durable, excessive force during print removal can cause damage.
• اسٽوريج: When not in use, store spare platforms flat and in a clean, dry environment to prevent warping or damage to the magnetic properties.

6. مسئلا حل ڪرڻ

هتي ڪجھ عام مسئلا ۽ انهن جا امڪاني حل آهن:

• Prints Not Sticking (Poor Adhesion):
  • Ensure the bed is properly leveled.
  • پليٽ فارم جي مٿاڇري کي IPA سان چڱي طرح صاف ڪريو.
  • Increase the bed temperature slightly (within filament specifications).
  • Apply a thin layer of adhesion aid (e.g., glue stick) if necessary.
• Prints Sticking Too Much (Difficult Removal):
  • Allow the platform and print to cool completely before attempting removal.
  • پرنٽ ڇڏڻ لاءِ مقناطيسي پليٽ فارم کي نرميءَ سان موڙ ڏيو.
  • Avoid using excessive adhesion aids if not required.
• Warping of Prints:
  • Ensure proper bed leveling.
  • Check for drafts around the printer.
  • Adjust bed temperature and print settings for the specific filament being used.

7. استعمال ڪندڙ ٽوٽڪا

• Rotate Platforms: If you notice wear in a specific area, rotate the platform or use a different one from the 3-piece set to distribute wear evenly.
• نرم هٽائڻ: Always allow prints to cool before removal. For stubborn prints, a gentle twist or flex of the platform is usually sufficient. Avoid prying with metal tools directly on the surface.
• صاف رکو: A clean print surface is the most critical factor for good first layer adhesion. Make cleaning with IPA a routine part of your pre-print checklist.

8. وارنٽي ۽ سپورٽ

For any questions, technical support, or warranty inquiries regarding your Easythreed K10 Magnetic Build Platform, please contact the seller or manufacturer directly. Keep your purchase records for reference.