AKO D14918 Programming Key Instruction Manual

D149H181 Ed.08

AKO-D14918

جي AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

ڊيڄاريندڙ

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

وصف

1. LED COM
2. رڪارڊ ڪي
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. ايل ڪيو ويو
6. CONNECTOR CABLE

مطابقت

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

وائرنگ

1. اهم: Pay attention to the orientation of the connector.
2. AKO-80018 
   (اختياري)
3. AKO-D14918

بجلي جي فراهمي

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

آپريشن

اهم: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

ايل ڪيو ويو

Steady or flashing: Indicates that the key is connected to the controller.

LED COM

مستحڪم: Indicates an error in the transmission/reception of data
تڪڙو چمڪندڙ: Indicates transmission/reception of data in progress. At the end of the transmission LED COM بند ڪري ڇڏيندو.
سست چمڪائڻ: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

نوٽ: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

اهم: ڪڏهن به نه disconnect the programming key during data transmission.

ٽيڪنيڪل وضاحتون

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
سپلائي جلدtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
ماحولياتي وضاحتون:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO Electromecánica, SA
Av. Roquetes، 30-38 | 08812 سانت پيري ڊي ريبز | بارسلونا | اسپينا

35D149181 REV.07 2025

اسان مواد جي فراهمي جو حق محفوظ رکون ٿا جيڪي اسان جي ٽيڪنيڪل شيٽس ۾ بيان ڪيل شين کان ٿورو مختلف هجن.
تازه ڪاري معلومات اسان تي موجود آهي webسائيٽ.