1. تعارف
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampلائفائر. انسٽال ڪرڻ يا هلائڻ جي ڪوشش ڪرڻ کان اڳ مھرباني ڪري ھن دستور کي چڱي طرح پڙھو amplifier to ensure optimal performance and safety.
2. حفاظت جي ڄاڻ
انسٽاليشن ۽ آپريشن دوران هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:
- Disconnect the vehicle's negative battery terminal before any wiring connections are made.
- پڪ ڪريو ته سڀئي وائرنگ صحيح طريقي سان روٽ ٿيل ۽ محفوظ آهن ته جيئن نقصان يا شارٽ سرڪٽ کي روڪي سگهجي.
- انسٽاليشن سيڪشن ۾ بيان ڪيل بجلي ۽ زميني ڪنيڪشن لاءِ مناسب گيج وائرنگ استعمال ڪريو.
- جبل ampلائفائر کي محفوظ طور تي اهڙي جاءِ تي رکو جيڪو مناسب هوا جي وهڪري جي اجازت ڏئي ۽ نمي ۽ گهڻي گرمي کان محفوظ هجي.
- ڪم نه ڪريو amplifier if it is damaged or malfunctioning. Refer to the troubleshooting section or seek professional assistance.
3. پراڊڪٽ ختمview
The Lanzar VIBE211 is a 2-channel Mosfet amplifier designed for car audio systems. It features a bridgeable design, allowing for flexible configuration, and incorporates a regulated Mosfet power supply for stable performance. Key features include variable high/low pass crossover controls and a remote subwoofer bass control.
هڪ زاويه وارو view of the silver Lanzar VIBE211 Vibe 360 Watt 2 Channel Mosfet Ampلائفائر، شوڪasing its finned heatsink design, RCA inputs, and control panel. The amplifier features text indicating 'bridgeable 2 channel amplifier', 'vibe 211', 'Lanzar vibe', '360 watts', 'high/low pass crossover', and 'regulated mosfet power supply'. A small, separate remote bass level control unit is visible in the foreground.
4. سيٽ اپ ۽ تنصيب
4.1 چڙهڻ Ampزندگي گذاريندڙ
Choose a secure mounting location that provides adequate air circulation around the amplifier's heatsink. Avoid mounting in direct sunlight or areas prone to moisture. Use the provided mounting hardware to secure the ampلفٽ کي مضبوطيءَ سان مضبوط مٿاڇري تي لڳايو.
4.2 وائرنگ ڪنيڪشن
Ensure all connections are tight and properly insulated to prevent short circuits.
- Power (B+): Connect a heavy-gauge wire (e.g., 8 AWG or larger) directly from the positive terminal of the vehicle's battery to the amplifier's B+ terminal. Install an appropriate fuse (15A) within 18 inches of the battery.
- گرائونڊ (GND): Connect a heavy-gauge wire of the same size as the power wire from the amplifier's GND terminal to a clean, unpainted metal surface of the vehicle chassis. Ensure a good electrical connection.
- ريموٽ (REM): Connect a smaller gauge wire (e.g., 18 AWG) from the ampلائيفائر جي آر اي ايم ٽرمينل کي توهان جي هيڊ يونٽ جي ريموٽ ٽرن آن آئوٽ پُٽ ڏانهن. هي تار موڙي ٿو ampپنهنجي اسٽيريو سان لائفائر آن ۽ آف ڪريو.
- آر سي سي انٽس: Connect the RCA audio cables from your head unit's pre-amp کي آئوٽ پُٽ amplifier's Gold RCA Inputs. The amplifier includes Line Outs for Left and Right Channels for daisy-chaining to other ampجان بچائيندڙ.
- اسپيڪر آئوٽ پُٽ: Connect your speakers to the amplifier's speaker terminals. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and bridgeable at 4 Ohms.
- Remote Subwoofer Bass Control: Connect the remote bass control unit to the designated port on the amplifier. Mount the control unit in an accessible location for easy adjustment.
5. آپريٽنگ هدايتون
5.1 شروعاتي پاور اپ
After all connections are made, reconnect the vehicle's negative battery terminal. Turn on your head unit. The amplifier features Soft Turn On/Off circuitry to prevent pops and clicks. Power Protection LED Indicators will illuminate to show operational status.
5.2 Adjusting Input Level Controls
جي amplifier has Variable Input Level Controls. Start with the amplifier's input level set to minimum. Play a familiar piece of music through your head unit at about 75% of its maximum volume. Slowly increase the ampلائفائر جي ان پٽ ليول کي جيستائين توهان کي معمولي تحريف نه ٻڌي، پوءِ ان کي ٿورو پوئتي هٽايو. اهو يقيني بڻائي ٿو ته ampلائفائر ڪلپنگ کان سواءِ هڪ بهترين سگنل حاصل ڪري ٿو.
5.3 ڪراس اوور سيٽنگون
جي amplifier features Variable High Low Pass Crossover Controls. These allow you to filter specific frequencies to your speakers or subwoofers.
- هاء پاس فلٽر (HPF): Used for full-range speakers to prevent low frequencies from reaching them, improving clarity.
- گهٽ پاس فلٽر (ايل پي ايف): Used for subwoofers to allow only low frequencies to pass, enhancing bass response.
Adjust these controls to match the frequency response characteristics of your speakers and subwoofers.
5.4 Bass Boost Circuit
The built-in Bass Boost Circuit allows for an increase in bass output at specific frequencies. Use this feature sparingly and adjust to your preference, avoiding excessive boosting that could lead to distortion or speaker damage.
5.5 برجڊ موڊ آپريشن
جي amplifier can be bridged at 4 Ohms to combine the power of both channels into a single, higher-power output, typically for driving a subwoofer. Refer to the wiring diagram for specific instructions on bridging the ampوierيڪ زنده
6. سار سنڀال
The Lanzar VIBE211 amplifier requires minimal maintenance. Periodically inspect the wiring connections for tightness and corrosion. Keep the amplifier's heatsink clean and free of dust or debris to ensure proper cooling. Use a soft, dry cloth for cleaning the exterior.
7. مسئلا حل ڪرڻ
جيڪڏهن توهان پنهنجي سان مسئلا محسوس ڪندا آهيو ampلائفائر، پيشه ورانه خدمت حاصل ڪرڻ کان اڳ هيٺ ڏنل جدول سان صلاح ڪريو:
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| ڪابه طاقت / ڪابه آواز ناهي | ڦاٽل فيوز؛ ڍلو پاور/گرائونڊ/ريموٽ تار؛ ناقص هيڊ يونٽ. | Check and replace fuse; Verify all power, ground, and remote connections; Test head unit functionality. |
| بگڙيل آواز | Input level too high; Speaker impedance too low; Damaged speakers. | Adjust input level; Verify speaker impedance (2 Ohm stereo stable, 4 Ohm bridged); Inspect speakers for damage. |
| Amplifier Goes into Protection Mode | وڌيڪ گرم ٿيڻ؛ اسپيڪر وائرنگ ۾ شارٽ سرڪٽ؛ گهٽ وولٽtage. | Ensure adequate ventilation; Check speaker wires for shorts; Verify battery voltage and charging system. |
| سب ووفر مان ڪو به باس ناهي | LPF not enabled or set too high; Phase issue; Remote bass control set to minimum. | Adjust LPF setting; Check subwoofer phase; Increase remote bass control level. |
8. وضاحتون
Technical specifications for the Lanzar VIBE211 ampزنده:
- Power Output (RMS @ 4 Ohms): 2 x 90 واٽ
- Power Output (Max @ 4 Ohms): 2 x 180 واٽ
- Power Output (Max Bridged @ 4 Ohms): 1 x 360 واٽ
- Power Output (RMS @ 2 Ohms): 2 x 150 واٽ
- Ampزنده قسم: 2 Channel Mosfet
- تعدد جواب: 15 Hz - 35 kHz
- سگنل کان شور جو تناسب (S/N): 90 ڊي بي
- فيوز جي درجه بندي: 15 اي
- ڊائرنس (ڊبليو ايڇ ڊي ايل): 10.25 انچ x 2 انچ x 8 انچ
- ان پٽ ليول ڪنٽرول: متغير
- ڪراس اوور ڪنٽرول: Variable High/Low Pass
- استحڪام: 2 Ohm Stereo Stable, Bridgeable at 4 Ohms
- حفاظتي سرڪٽ: Advanced Power Protection LED Indicators
- اضافي خاصيتون: Remote Subwoofer Bass Control, Electronic Crossover Network, Bass Boost Circuit, Soft Turn On/Off
9. وارنٽي ۽ سپورٽ
9.1 وارنٽي ڄاڻ
The Lanzar VIBE211 amplifier سان اچي ٿو a 1-سال limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. The warranty does not cover damage caused by improper installation, accident, misuse, abuse, negligence, or unauthorized modification.
9.2 ڪسٽمر سپورٽ
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Lanzar customer support. Refer to the official Lanzar webموجوده رابطي جي معلومات لاءِ سائيٽ يا پراڊڪٽ پيڪنگنگ.
