Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. حفاظت جي ڄاڻ

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• ھدايت پڙھو: Read and understand all instructions and warnings in this manual before using this product.
• Use on Hard, Level Surface: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• گنجائش کان وڌيڪ نه ڪريو: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• جڪ اسٽينڊ استعمال ڪريو: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• Center the Load: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• حفاظتي سامان پائڻ: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• صاف رکو: Keep hands, feet, and other body parts clear of moving parts and the vehicle during lifting and lowering.
• استعمال ڪرڻ کان اڳ چڪاس ڪريو: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• مناسب اسٽوريج: Store the jack in a clean, dry place, fully lowered, when not in use.

2. پراڊڪٽ ختمview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

اهم اجزاء:

• هٿ کڻڻ: The main arm that raises and lowers the vehicle.
• سيڊل: The contact point with the vehicle's lifting area.
• سنڀال: Used for pumping to lift and rotating to lower.
• ڇڏڻ جو والو: Controls the lowering speed of the jack.
• Wheels/Casters: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

شڪل 2: پاسي view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. سيٽ اپ

شروعاتي تياري:

1. پيڪنگ کولڻ: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. اسيمبليء جو انتظام: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

هائيڊولڪ سسٽم ۾ رت وهڻ:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. کليل رليز والو: Turn the handle counter-clockwise to fully open the release valve.
2. پمپ هينڊل: Pump the handle 6-8 full strokes to force air out of the system.
3. رليز والو بند ڪريو: رليز والو کي بند ڪرڻ لاءِ ھينڊل کي گھڙي جي طرف ڦيرايو.
4. ٽيسٽ: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. آپريٽنگ هدايتون

Lifting a Vehicle:

1. گاڏي تيار ڪريو: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
2. Position Jack: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. رليز والو بند ڪريو: Turn the handle clockwise until the release valve is firmly closed. Do not overtighten.
4. لفٽ گاڏي: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. Secure with Jack Stands: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Slightly Lower onto Stands: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

Lowering a Vehicle:

1. Reposition Jack: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. Remove Jack Stands: Carefully remove the jack stands from under the vehicle.
3. هيٺيون گاڏي: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Fully Lower: Once the vehicle is fully lowered, remove the jack.

5. سار سنڀال

Regular maintenance ensures the longevity and safe operation of your hydraulic floor jack.

• هائيڊولڪ فلوئڊ ليول: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• لوڻ: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• صفائي: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• اسٽوريج: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

6. مسئلا حل ڪرڻ

7. وضاحتون

• ماڊل: W1612
• لوڊ گنجائش: 5,000 پائونڊ (2.5 ٽن)
• وڌ ۾ وڌ کڻڻ جي اوچائي: 19.25 انچ
• Minimum Lifting Height: Approximately 5 inches (standard floor jack minimums)
• مواد: مصر جو اسٽيل
• شيء جو وزن: 79.7 پائونڊ
• پيداوار جي ماپ (L x W x H): 30.6 x 8.6 x 15.4 انچ
• گاڏين جي خدمت جو قسم: ڪار، ٽرڪ

8. وارنٽي ۽ سپورٽ

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

ٺاهيندڙ: Performance Tool (Wilmar Corporation)

UPC: 039564124778

تاريخ پهرين دستياب: اپريل 1، 2004