RAB لائيٽنگ LFP16A سليڪ فلڊ لائيٽ هدايت نامو

1. پراڊڪٽ ختمview

The RAB Lighting LFP16A Sleek Floodlight is designed for outdoor illumination, providing efficient and durable lighting. This fixture accommodates a PAR16 type bulb and features a robust die-cast aluminum housing with a powder-coated finish for enhanced durability and weather resistance.

اهم خاصيتون:

• Designed for 60W PAR16 bulbs, delivering 650 lumens output (bulb not included).
• Durable die-cast aluminum housing with a powder-coated finish.
• Gasket and O-ring seals provide resistance against weather elements.
• Integrated shield helps reduce glare.
• Equipped with a 1/2" NPS threaded arm for secure mounting and a locking swivel for adjustable positioning.

Figure 1: RAB Lighting LFP16A Sleek Floodlight. This image shows the floodlight fixture with its threaded arm and wiring, highlighting its compact and durable design.

2. حفاظت جي ڄاڻ

مھرباني ڪري ھن پراڊڪٽ کي انسٽال ڪرڻ يا هلائڻ کان پھريان سڀ ھدايتون پڙھو ۽ سمجھو. انھن ھدايتن تي عمل ڪرڻ ۾ ناڪامي جي نتيجي ۾ بجلي جو جھٽڪو، باهه، يا ٻيا خطرا ٿي سگھن ٿا جيڪي ملڪيت کي نقصان يا ذاتي زخم پھچائي سگھن ٿا.

• برقي حفاظت: Always disconnect power at the circuit breaker or fuse box before wiring or servicing the fixture.
• قابل اليڪٽريشن: تنصيب سڀني مقامي ۽ قومي اليڪٽريڪل ڪوڊن جي مطابق هڪ قابل اليڪٽريشن طرفان ڪئي وڃي.
• گرائونڊنگ: Ensure the fixture is properly grounded to avoid potential electrical hazards.
• بلب جو قسم: Use only PAR16 type bulbs with a maximum wattag60W جو e. وڌ ۾ وڌ واٽ کان وڌيڪtage فڪسچر کي وڌيڪ گرم ڪرڻ ۽ نقصان پهچائي سگھي ٿو.
• گندي جڳھ: This fixture is suitable for wet locations. Ensure all connections are properly sealed and waterproofed during installation.
• گرمي پد: Do not install near combustible materials or surfaces that may be affected by heat.

3. پيڪيج مواد

انسٽاليشن شروع ڪرڻ کان اڳ پڪ ڪريو ته سڀئي جزا موجود آهن:

• RAB Lighting LFP16A Sleek Floodlight Fixture (1)
• هدايت نامو (1)

Note: Light bulb and wire connectors are not included and must be purchased separately.

4. سيٽ اپ ۽ تنصيب

This floodlight is designed for wall mounting and features a 1/2" NPS threaded arm for secure attachment to a junction box or mounting accessory. Follow these steps for proper installation:

1. انسٽاليشن لاء تيار ڪريو:
   • Turn off power at the circuit breaker before starting any electrical work.
   • Gather necessary tools: screwdriver, wire strippers, electrical tape, silicone sealant (for waterproofing).
2. فڪسچر لڳايو:
   • Thread the 1/2" NPS arm of the floodlight into a compatible outdoor junction box or mounting plate. Ensure a tight and secure connection.
   • Use the locking swivel to adjust the initial angle of the fixture.
   

   Figure 2: Detail of the 1/2" NPS threaded arm and 180-degree adjustable swivel. This illustrates the mounting mechanism and flexibility of the floodlight.
3. وائرنگ ڪنيڪشن:
   • Connect the black wire from the fixture to the hot (black) wire from the power supply.
   • Connect the white wire from the fixture to the neutral (white) wire from the power supply.
   • Connect the bare copper or green wire from the fixture to the ground wire from the power supply.
   • Secure all connections with appropriate wire connectors and electrical tape. For outdoor installations, consider using silicone-filled wire nuts for added moisture protection.
4. بلب انسٽال ڪريو:
   • Carefully insert a PAR16 bulb (max 60W) into the fixture socket. Do not overtighten.
5. Seal and Test:
   • Ensure all connections are secure and the fixture is properly sealed against moisture. Apply silicone sealant around the mounting base if necessary.
   • Restore power at the circuit breaker and test the floodlight's operation.

5. آپريٽنگ هدايتون

Once installed and powered, the RAB Lighting LFP16A Floodlight operates by the control of the circuit it is connected to (e.g., a wall switch, timer, or photocell). There are no direct controls on the fixture itself.

• روشني جي هدايت کي ترتيب ڏيڻ: The fixture features a locking swivel arm. To adjust the light direction, loosen the locking nut on the swivel, position the floodlight as desired, and then tighten the locking nut securely.
• چمڪ گھٽائڻ: The built-in shield is designed to minimize glare, directing light effectively to the intended area.

شڪل 3: مثالample of the LFP16A floodlight used in a landscape setting, demonstrating its illumination capabilities.

6. سار سنڀال

Regular maintenance ensures optimal performance and longevity of your floodlight.

• صفائي: وقتي طور تي فڪسچر جي ٻاهرين حصي کي نرم، ڊي سان صاف ڪريوamp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish. Ensure power is off before cleaning.
• بلب مٽائڻ:
  1. سرڪٽ بريڪر تي فڪسچر جي بجلي بند ڪريو.
  2. Allow the old bulb to cool completely before handling.
  3. Carefully unscrew and remove the old PAR16 bulb.
  4. Insert a new PAR16 bulb (max 60W) into the socket, ensuring it is seated correctly.
  5. Restore power and test the new bulb.
• چڪاس: Annually inspect the fixture for any signs of wear, damage, or loose connections. Address any issues promptly.

7. مسئلا حل ڪرڻ

8. وضاحتون

9. وارنٽي ۽ سپورٽ

The RAB Lighting LFP16A Sleek Floodlight comes with a 1 سالن جي ٺاهيندڙ جي وارنٽي خريداري جي تاريخ کان. هي وارنٽي عام استعمال هيٺ مواد ۽ ڪاريگري ۾ خرابين کي ڍڪيندي آهي.

For warranty claims, technical support, or further assistance, please contact RAB Lighting customer service. Refer to the official RAB Lighting webجديد ترين رابطي جي معلومات لاءِ سائيٽ.

ٺاهيندڙ: RAB روشني

Webسائيٽ: www.rablighting.com (مثالampلي لنڪ، اصل لنڪ مختلف ٿي سگهي ٿو)