Wave BJ-05 Purasapo 5mm اختياري سسٽم سيريز هدايت نامو

تعارف

This manual provides instructions for the Wave BJ-05 Purasapo 5mm Optional System Series (Model OP413). This product consists of detailed plastic parts designed for use with various plastic models, offering enhanced customization and structural support. It is intended for hobbyists and modelers looking to add fine details or modify their existing plastic kits.

حصن جي فهرست

The Wave BJ-05 Purasapo set includes the following components on a single sprue. Refer to the image below for visual identification of each part, numbered 1 through 7.

Image Description: A gray plastic sprue containing various small, numbered components. The packaging behind the sprue is blue and white, displaying the brand "Wave" and model number "OP-413-300". The parts include cylindrical connectors, square bases, and circular supports.

• حصو 1: Cylindrical connectors (multiple pieces)
• حصو 2: Small circular bases (multiple pieces)
• حصو 3: Square bases with central circular holes (two pieces)
• حصو 4: Solid square bases (two pieces)
• حصو 5: Circular connectors with central holes (multiple pieces)
• حصو 6: Circular connectors with central holes (multiple pieces, slightly different from Part 5)
• حصو 7: Single cylindrical connector

سيٽ اپ ۽ اسيمبلي

These parts are intended for advanced modelers to customize or enhance plastic models. Follow these general steps for integration:

1. تياري: Carefully remove the desired parts from the sprue using a hobby knife or nippers. Ensure clean cuts to avoid damaging the parts. Smooth any rough edges with a fine-grit sanding stick or file.
2. فيشن: Test fit the parts with your plastic model before applying any adhesive. Some parts may require minor sanding or trimming for a perfect fit. Do not force parts into place.
3. ملائڻ: Use appropriate plastic model cement or adhesive to secure the parts in place. Apply adhesive sparingly to avoid excess. Allow sufficient drying time as per the adhesive manufacturer's instructions before handling.
4. حسب ضرورت: These parts can be painted or modified further to match your model's aesthetic. Ensure paint is compatible with plastic model materials.

سنڀال ۽ سار سنڀال

To ensure the longevity of your model and its added components, observe the following care guidelines:

• Keep assembled models away from direct sunlight and extreme temperatures to prevent plastic warping, discoloration, or degradation.
• Clean parts gently with a soft, dry cloth or a soft brush. Avoid harsh chemicals, solvents, or abrasive materials that may damage the plastic or paint finish.
• Store unused parts in a cool, dry place, preferably in their original packaging or a sealed container, to prevent loss, dust accumulation, or damage.

مشڪلاتون

This section addresses common issues encountered during the use of these optional parts.

• حصو مناسب نه آهي:
  حل: Carefully check the intended connection point on your model and the orientation of the part. Minor adjustments with a hobby file or fine-grit sandpaper may be necessary. Do not force parts, as this can cause breakage to both the part and your model.
• Part Breaks During Removal from Sprue:
  حل: Always use sharp nippers or a hobby knife for clean cuts, cutting slightly away from the part and then trimming flush. If a part breaks, plastic cement can often repair it, but care must be taken to maintain structural integrity and appearance.
• Adhesive Issues (e.g., weak bond, melted plastic):
  حل: Ensure surfaces are clean and dry before applying adhesive. Use a minimal amount of plastic model cement to avoid melting or damaging the plastic. For stronger bonds, consider using a two-part epoxy or super glue, ensuring compatibility with plastic. Allow adequate curing time without disturbance.

وضاحتون

وارنٽي ۽ سپورٽ

This product is designed as an optional accessory for plastic models. Due to the nature of hobby parts and their integration into various projects, specific warranties may vary. For support regarding manufacturing defects or missing components, please contact your retailer or the manufacturer, Wave, directly. It is recommended to keep your purchase receipt as proof of purchase.