1. تعارف
خريد ڪرڻ لاءِ مهربانيasing the Sanwa Electric Tool Keystone Cutter SG-230B. This tool is designed for efficient and precise cutting of various metal sheets, particularly corrugated thick plates such as deck plates and C-channels. Please read this manual thoroughly before operating the tool to ensure safe and effective use. Keep this manual in a safe place for future reference.
Image of the Sanwa SG-230B Keystone Cutter, a corded electric tool designed for cutting metal sheets.
2. حفاظتي هدايتون
بجلي جا اوزار استعمال ڪرڻ وقت باهه، بجليءَ جي جھٽڪي، ۽ ذاتي زخمن جي خطري کي گهٽائڻ لاءِ هميشه بنيادي حفاظتي احتياطن تي عمل ڪريو.
- ڪم واري علائقي جي حفاظت: پنهنجي ڪم واري علائقي کي صاف ۽ روشن رکو. گندو يا اونداهو علائقو حادثن کي دعوت ڏئي ٿو. بجلي جا اوزار ڌماڪيدار ماحول ۾ نه هلايو، جهڙوڪ ٻرندڙ مائع، گئس، يا مٽي جي موجودگي ۾.
- برقي حفاظت: پاور ٽول پلگ کي آئوٽ ليٽ سان ملائڻ گهرجي. ڪڏهن به پلگ کي ڪنهن به طرح تبديل نه ڪريو. ڪنڊ جو غلط استعمال نه ڪريو. ڪڏهن به پاور ٽول کي کڻڻ، ڇڪڻ، يا ان پلگ ڪرڻ لاءِ ڪنڊ استعمال نه ڪريو. ڪنڊ کي گرمي، تيل، تيز ڪنارن، يا حرڪت ڪندڙ حصن کان پري رکو.
- ذاتي حفاظت: Always wear eye protection. Use dust mask, non-skid safety shoes, hard hat, or hearing protection for appropriate conditions. Do not overreach. Keep proper footing and balance at all times. Dress properly. Do not wear loose clothing or jewelry.
- اوزار استعمال ۽ سنڀال: پاور ٽول کي زور سان نه لڳايو. پنهنجي ايپليڪيشن لاءِ صحيح پاور ٽول استعمال ڪريو. ڪا به ترتيب ڏيڻ، لوازمات تبديل ڪرڻ، يا پاور ٽولز کي ذخيرو ڪرڻ کان اڳ پاور سورس کان پلگ ڊسڪنيڪٽ ڪريو.
- سار سنڀال: بجلي جا اوزار برقرار رکڻ. جانچيو هلندڙ حرڪت وارن حصن جي غلط بي ترتيبي يا پابند ڪرڻ ، حصن کي ٽوڙڻ ۽ ڪنهن ٻئي حالت جيڪا طاقت جي ٽول جي آپريشن تي اثر انداز ٿي سگھي ٿي. جيڪڏهن نقصان پهچايو ، استعمال ڪرڻ کان پهريان طاقت جو اوزار مرمت ڪيو.
3. سيٽ اپ
Before initial use, ensure the tool is properly set up.
- پيڪنگ کولڻ: Carefully remove the Keystone Cutter from its packaging. Inspect the tool for any signs of damage that may have occurred during shipping.
- پاور ڪنيڪشن: This tool operates on AC100V. Ensure your power outlet matches this voltage. The power cord length is 2.4 meters. Connect the tool to a suitable power source.
- ورڪ پيس جي تياري: Secure the material to be cut firmly to prevent movement during operation. Mark your cutting line clearly.
- بلڊ جي چڪاس: Before each use, check the cutting blade for sharpness and any damage. A dull or damaged blade can affect cutting performance and safety.
4. آپريٽنگ هدايتون
Follow these steps for safe and effective operation of the Keystone Cutter.
- ڪٽ شروع ڪرڻ: Position the cutter on the edge of the material or at the designated pilot hole for mid-cut operations. Ensure the cutting head is stable.
- پاور آن: Press the power switch to start the motor. Allow the tool to reach full speed before engaging the material.
- ڪٽڻ: Guide the tool along the marked cutting line with steady, even pressure. Do not force the tool; let the blade do the work. The cutting capacity for mild steel plate is 2.3mm and for stainless steel is 1.2mm. The cutting width is 6mm.
- Mid-Cut Operation: For internal cuts, a pilot hole of at least 29mm is required. Insert the cutting head into the pilot hole and then proceed with cutting as described above.
- گھٽ ۾ گھٽ ڪٽڻ وارو ريڊيس: The tool is capable of cutting curves with a minimum radius of 60mm.
- ڪٽ ختم ڪرڻ: Once the cut is complete, release the power switch and wait for the blade to stop completely before setting the tool down.
5. سار سنڀال
باقاعده سار سنڀال بهترين ڪارڪردگي کي يقيني بڻائي ٿي ۽ توهان جي اوزار جي زندگي وڌائي ٿي.
- صفائي: After each use, disconnect the tool from the power supply and clean off any metal shavings or dust from the cutting head and ventilation openings using a brush or compressed air.
- بليڊ متبادل: Replace dull or damaged blades promptly. Refer to the manufacturer's instructions for specific blade replacement procedures.
- لوڻ: Periodically apply a small amount of appropriate lubricant to moving parts as recommended by the manufacturer to ensure smooth operation.
- اسٽوريج: اوزار کي سڪل، محفوظ جاءِ تي، ٻارن جي پهچ کان پري رکو.
6. مسئلا حل ڪرڻ
If you encounter issues with your Keystone Cutter, refer to the following common problems and solutions.
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| اوزار شروع نٿو ٿئي | بجلي جي فراهمي ناهي؛ خراب ٿيل بجلي جي تار؛ خراب سوئچ | Check power connection; Inspect cord for damage; Contact service for switch replacement |
| خراب ڪٽڻ جي ڪارڪردگي | Dull or damaged blade; Incorrect cutting technique; Overloading the tool | بليڊ تبديل ڪريو؛ ٻيهرview operating instructions; Do not force the tool |
| گھڻي واڪ يا شور | Loose components; Damaged internal parts; Worn blade | Check for loose screws; Contact service for inspection; Replace blade |
If the problem persists after attempting these solutions, please contact an authorized service center.
7. وضاحتون
Technical specifications for the Sanwa Electric Tool Keystone Cutter SG-230B.
| خاصيت | تفصيل |
|---|---|
| برانڊ | سانوا |
| ماڊل نمبر | ايس جي 230 بي |
| موجوده درجه بندي | 6.5 اي |
| بجلي جو استعمال | 520 ڊبليو |
| Cutting Capacity (Mild Steel Plate) | 2.3 ملي ميٽر |
| Cutting Capacity (Stainless Steel) | 1.2 ملي ميٽر |
| گھٽ ۾ گھٽ ڪٽڻ واري ريڊيس | 60 ملي ميٽر |
| ڪٽڻ جي ويڪر | 6 ملي ميٽر |
| طاقت جو ذريعو | AC100V |
| ڪنڊ ڊگھائي | 2.4 م |
| پيداوار جو وزن | 2.8 ڪلو |
| پيڪيج جي ماپ | 44.3 x 20.7 x 11.8 سينٽي |
8. وارنٽي ۽ سپورٽ
Specific warranty details and support contact information are not available in the provided product data. For warranty claims, technical support, or service inquiries, please refer to the documentation included with your product packaging or visit the official Sanwa webسڀ کان وڌيڪ تازه ترين معلومات لاء سائيٽ.
9. پراڊڪٽ وڊيوز
No official product videos were provided in the available data for this item.
