Sealey IHS1 Stand for IWMH1809R/IFSH1809R Heaters - Instruction Manual

1. تعارف

This manual provides essential instructions for the safe assembly, operation, and maintenance of your Sealey IHS1 stand. This stand is designed to convert the Sealey IWMH1809R wall-mounted infrared heater into a freestanding IFSH1809R unit. Please read these instructions thoroughly before use and retain them for future reference.

Figure 1: The Sealey IHS1 stand with a compatible infrared heater installed, showcasing ان جي فري اسٽينڊنگ ڊيزائن.

2. حفاظتي هدايتون

Always observe the following safety precautions to prevent personal injury or damage to the product.

• Ensure the stand is assembled on a flat, stable, and level surface.
• Do not exceed the maximum weight capacity of the stand. This stand is specifically designed for Sealey IWMH1809R/IFSH1809R heaters.
• Regularly inspect all fasteners and connections to ensure they are secure.
• Keep children and pets away from the stand and attached heater during operation.
• ڪنهن به طرح اسٽينڊ کي تبديل ڪرڻ جي ڪوشش نه ڪريو.
• When moving the stand with the heater attached, ensure the heater is switched off and cooled, and move with care to prevent tipping.

3. پيڪيج مواد

اسيمبلي شروع ڪرڻ کان اڳ پڪ ڪريو ته سڀئي جزا موجود آهن:

• 1 x Sealey IHS1 Stand Assembly (includes base, pole sections, and mounting bracket)
• Required Fasteners and Tools (if applicable, refer to heater manual for heater-specific fasteners)

4. سيٽ اپ ۽ اسيمبلي

Follow these steps to assemble the IHS1 stand and attach your compatible heater.

1. بنياد گڏ ڪريو: Place the stand base on a flat, stable surface. Ensure the base is fully seated and stable.
   

   Figure 2: The robust circular base of the Sealey IHS1 stand, designed for stability.

2. قطب جا حصا ڳنڍيو: Securely connect the pole sections to the base and to each other, following the instructions provided with the stand's packaging. Ensure all connections are tightened.
3. هيٽر لڳايو: Attach your Sealey IWMH1809R heater to the top mounting bracket of the IHS1 stand. Refer to your heater's instruction manual for specific mounting hardware and procedures. Ensure the heater is securely fastened and balanced on the stand.
4. ڪيبل جو انتظام: Route the heater's power cable along the stand pole using the provided cable clips to prevent tripping hazards and maintain a tidy appearance.
   

   شڪل 3: هڪ ويجهو تصوير view of the cable management clip on the stand's pole, used to secure the power cord.

5. آپريٽنگ هدايتون

The IHS1 stand provides a stable platform for your heater. Its primary operational feature is height adjustment.

1. اوچائي کي ترتيب ڏيڻ: To adjust the height of the heater, loosen the height adjustment collar on the stand pole. Carefully raise or lower the upper pole section to the desired height (between 1340mm and 1700mm). Once the desired height is achieved, securely tighten the adjustment collar to lock the pole in place.
   

   Figure 4: The height adjustment collar on the stand's pole, allowing for variable height settings.
2. پوزيشن: Place the stand with the attached heater in a location where it can provide optimal heating without obstruction. Ensure there is adequate clearance around the heater as specified in the heater's manual.
   

   Figure 5: The Sealey IHS1 stand with an infrared heater positioned outdoors, demonstrating its freestanding utility.

Note: For specific operating instructions regarding the heater's power, heat settings, and sensor functions, please refer to the instruction manual provided with your Sealey IWMH1809R/IFSH1809R heater. An example of a heater control panel is shown below for reference.

شڪل 6: مثالample of a control panel found on compatible Sealey heaters, featuring ON, OFF, and SENSOR buttons.

6. سار سنڀال

To ensure the longevity and safe operation of your IHS1 stand:

• صفائي: اسٽينڊ کي نرم، ڊي سان صاف ڪريوamp ڪپڙو. استعمال نه ڪريو abrasive cleaners يا solvents.
• چڪاس: Periodically check all bolts, screws, and connections for tightness. Retighten if necessary.
• اسٽوريج: If storing the stand for an extended period, disassemble it if desired and store in a dry, protected area.

7. مسئلا حل ڪرڻ

If you encounter issues with your IHS1 stand, consider the following:

• اسٽينڊ جي عدم استحڪام:
  • Ensure the stand is on a completely flat and level surface.
  • Verify all pole sections and the base are securely tightened.
  • Confirm the heater is properly centered and balanced on the mounting bracket.
• اوچائي کي ترتيب ڏيڻ ۾ مشڪل:
  • Ensure the height adjustment collar is fully loosened before attempting to adjust.
  • Check for any obstructions or debris within the pole sections.

For issues related to the heater's functionality, refer to the heater's specific instruction manual.

8. وضاحتون

9. وارنٽي ۽ سپورٽ

This Sealey IHS1 stand comes with a 1 سال جي گارنٽي. For full terms and conditions, please refer to the official Sealey website or contact Sealey customer support.

Figure 7: Sealey's 1 Year Guarantee emblem, indicating product assurance.

For technical assistance, spare parts, or warranty claims, please contact your authorized Sealey dealer or visit the official Sealey webسپورٽ جي معلومات لاءِ سائيٽ.

Please note: "Terms and conditions apply" as indicated by the manufacturer.