Steinel 11221 Digi-Check 3 Digital Voltagاي جاچ ڪندڙ

1. تعارف

Thank you for choosing the Steinel 11221 Digi-Check 3 Digital Voltage Tester. This device is designed for reliable and accurate electrical measurements, including AC/DC voltage, phase, polarity, and continuity. Please read this manual thoroughly before use to ensure safe and optimal operation.

اهم خاصيتون:

• ڊجيٽل جلدtage testing for AC and DC up to 999 volts.
• Microprocessor-controlled for enhanced accuracy.
• Integrated phase and polarity testing functions.
• Continuity testing with a range of 0 to 500 kOhm.
• Clear digital display and LED indicators for easy reading.

2. حفاظتي هدايتون

ڊوائيس کي زخم يا نقصان کان بچڻ لاءِ هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:

• جيڪڏهن ڊوائيس خراب نظر اچي يا صحيح طريقي سان ڪم نه ڪري رهي هجي ته ان کي استعمال نه ڪريو.
• Ensure your hands are dry and you are standing on an insulated surface when performing electrical tests.
• Always verify the tester's functionality on a known live circuit before and after use.
• وڌ ۾ وڌ درجه بندي واري حجم کان وڌيڪ نه ڪريوtag999V AC/DC جو اي.
• This device is intended for professional use or by individuals with adequate electrical knowledge.
• ڊوائيس کي ٻارن کان پري رکو.
• Refer to local electrical safety regulations and standards.

3. پراڊڪٽ ختمview

The Steinel 11221 Digi-Check 3 consists of a main unit with a digital display and control buttons, and a separate test probe connected by a flexible cable.

Image 1: Steinel 11221 Digi-Check 3 Digital Voltage Tester. The image shows the main unit with a digital display and two orange buttons (HOLD and TEST), and a separate black test probe connected by a grey cable. Both probes have pointed tips.

اجزاء:

1. مکيه يونٽ: Houses the digital display, LEDs, and control buttons.
2. Test Probe (Red): Integrated into the main unit.
3. Test Probe (Black): Separate probe connected via cable.
4. ڊجيٽل ڊسپلي ڏيکاري ٿو جلدtage readings and other indicators.
5. LED اشارا: Provide visual feedback for various tests.
6. هولڊ بٽڻ: ڊسپلي تي موجوده پڙهڻ کي منجمد ڪري ٿو.
7. ٽيسٽ بٽڻ: Initiates specific test functions (e.g., continuity).

4. سيٽ اپ

The Steinel 11221 Digi-Check 3 is ready for use upon receipt. No initial battery installation is required as it is powered via the circuit being tested or an internal power source (if applicable, check product specifications for details on internal power). Ensure the probes and cable are free from damage before each use.

• Inspect the device for any visible damage to the casing, probes, or cable.
• Clean the probe tips if necessary to ensure good electrical contact.
• Perform a quick functional check on a known voltage source (e.g., a wall outlet) to confirm the device is operating correctly before testing unknown circuits.

5. آپريٽنگ هدايتون

5.1. جلدtagاي ماپ (اي سي/ڊي سي)

1. Connect the red probe to the positive or live terminal and the black probe to the negative or neutral/ground terminal of the circuit to be measured.
2. The digital display will automatically show the measured voltage value (AC or DC).
3. Observe the polarity indicator on the display for DC voltage ماپون.
4. کي دٻايو رکو ڊسپلي تي موجوده پڙهڻ کي منجمد ڪرڻ لاءِ بٽڻ. ڇڏڻ لاءِ ٻيهر دٻايو.

5.2. Phase Testing

To perform a phase test:

1. Touch the red probe to the conductor you wish to test for phase.
2. Simultaneously, touch the black probe to a known ground or neutral point.
3. The device will indicate the presence of phase voltage through an LED or specific display icon.

5.3. Polarity Testing

For DC circuits, the device automatically indicates polarity:

• جڏهن ماپڻ ڊي سي حجمtage, the digital display will show a '+' or '-' symbol next to the voltage reading, indicating the polarity of the red probe relative to the black probe.

5.4. لڳاتار جاچ

To check for continuity in a circuit or component:

1. Ensure the circuit is de-energized before performing continuity tests.
2. Touch the red and black probes to the two points you wish to test for continuity.
3. کي دٻايو ٽيسٽ button (if required, some models automatically detect continuity).
4. A low resistance reading (e.g., near 0 Ohm) and/or an audible tone/LED indicator signifies continuity. The device can test continuity up to 500 kOhm.

6. سار سنڀال

• صفائي: ڊوائيس کي نرم سان مسح ڪريو، ڊيamp ڪپڙو. گھڙڻ وارا صاف ڪندڙ يا محلول استعمال نه ڪريو. پڪ ڪريو ته ڊوائيس اسٽوريج يا ايندڙ استعمال کان اڳ سڪي وڃي.
• اسٽوريج: وول کي ذخيرو ڪريوtage tester in a dry, cool place, away from direct sunlight and extreme temperatures.
• جاچ جو معائنو: Regularly check the test probes and cable for cuts, cracks, or other damage. Replace if any damage is found.
• طاقت جو ذريعو: As the device is powered by the circuit under test or an internal source, no user-replaceable batteries are typically required. Refer to the product's specific technical data for any internal battery information.

7. مسئلا حل ڪرڻ

8. وضاحتون

9. وارنٽي ۽ سپورٽ

Steinel products are manufactured to high-quality standards and undergo rigorous quality control. For warranty information, technical support, or service inquiries, please refer to the official Steinel webسائيٽ تي وڃو يا پنهنجي مقامي ورهائيندڙ سان رابطو ڪريو. خريداري جي ثبوت طور پنهنجي خريداري جي رسيد رکو.

وڌيڪ مدد لاءِ، مھرباني ڪري دورو ڪريو Steinel official webسائيٽ.