1. تعارف
خريد ڪرڻ لاءِ مهربانيasing the Lanzar Max Pro 1800 Watt Mono Block Amplifier, Model MAXP1200. This manual provides essential information for the proper installation, operation, and maintenance of your amplifier. To ensure optimal performance and safety, please read this manual thoroughly before attempting to install or operate the unit. Keep this manual for future reference.
2. حفاظت جي ڄاڻ
زخم يا نقصان کان بچڻ لاءِ هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو amplifier and connected components.
- برقي حفاظت: Ensure all power connections are made correctly and securely. Disconnect the vehicle's battery before making any power connections to avoid electrical shorts. Use appropriate gauge wiring for power and ground connections as specified in the installation section.
- وينٽيليشن: انسٽال ڪريو amplifier in a location that allows for adequate air circulation. Do not cover the amplifier or install it in an enclosed space where heat cannot dissipate. Overheating can lead to amplifier shutdown or damage.
- پيشه ورانه تنصيب: If you are unsure about any aspect of the installation, it is recommended to seek assistance from a qualified car audio professional.
- نمي جي نمائش: بي نقاب نه ڪريو amplifier to moisture or water. This can cause electrical shock or damage to the unit.
- محفوظ لڳائڻ: جبل amplifier securely to prevent it from becoming a projectile in the event of a sudden stop or accident.
3. پراڊڪٽ ختمview
The Lanzar MAXP1200 is a high-performance mono block amplifier designed to deliver powerful and clear bass to your car audio system. Featuring 1800 watts of peak power, this amplifier is optimized for driving subwoofers.
Figure 3.1: Lanzar Max Pro 1800 Watt Mono Block Amplifier (Model MAXP1200). This image shows the amplifier's main body with its black ribbed heatsink design and the silver-colored side panel where the input and control terminals are located. The "Lanzar" logo is prominently displayed on the top surface.
اهم خاصيتون:
- Mono Block Design for dedicated subwoofer power.
- High Power Output: Up to 1800 Watts.
- MOSFET Power Supply for efficient operation.
- Variable Low Pass Crossover.
- Variable Bass Boost.
- Thermal, Overload, and Short Protection Circuitry.
اجزاء جي سڃاڻپ:
Refer to Figure 3.1 for a visual representation of the ampلائفائر جا اجزاء.
- آر سي اي انپٽس: For connecting the audio signal from your head unit.
- گينڊي ڪنٽرول: توهان جي هيڊ يونٽ جي آئوٽ پُٽ سان ملائڻ لاءِ ان پٽ حساسيت کي ترتيب ڏئي ٿو.
- Low Pass Filter (LPF) Control: Sets the upper frequency limit for the ampلائفائر جي پيداوار.
- باس بوسٽ ڪنٽرول: Increases the output level at a specific bass frequency.
- Power/Protect Indicators: LEDs that show the amplifier's operational status.
- پاور ٽرمينلز: Connections for +12V, Ground, and Remote Turn-On.
- اسپيڪر ٽرمينل: Output connections for your subwoofer(s).
4. سيٽ اپ ۽ تنصيب
توهان جي ڪارڪردگي ۽ ڊگهي عمر لاءِ صحيح تنصيب اهم آهي ampوierيڪ زنده
4.1 انسٽاليشن کان اڳ جاچ:
- پڪ ڪريو ته گاڏي جو برقي نظام سپورٽ ڪري سگهي ٿو amplifier's power requirements.
- Disconnect the negative terminal of the vehicle's battery before starting any wiring.
- Gather all necessary tools and wiring accessories (power wire, ground wire, remote wire, RCA cables, speaker wire, fuse holder, fuse).
4.2 چڙهڻ Ampزنده:
جي amplifier is designed for surface mount installation. Choose a mounting location that is:
- Secure and stable, preventing movement during vehicle operation.
- Well-ventilated, allowing heat to dissipate effectively. Avoid enclosed spaces like under carpets or in tight compartments.
- سڌي سج جي روشني يا گرمي جي ذريعن کان پري.
- Protected from moisture and excessive dust.
Use appropriate screws to secure the amplifier to the chosen surface. Ensure no existing wiring or fuel lines are damaged during drilling.
4.3 وائرنگ ڪنيڪشن:
- پاور (+12V) ڪنيڪشن: Run a power cable (e.g., 4-gauge or larger) directly from the positive terminal of the vehicle's battery to the amplifier's +12V terminal. Install an in-line fuse holder with an appropriate fuse (refer to specifications for fuse rating) within 18 inches (45 cm) of the battery.
- گرائونڊ (GND) ڪنيڪشن: پاور ڪيبل جي ساڳي گيج جي گرائونڊ ڪيبل کي ڳنڍيو amplifier's GND terminal to a clean, unpainted metal surface of the vehicle's chassis. Ensure a solid electrical connection by scraping away any paint or rust. The ground point should be as short as possible, ideally less than 3 feet (1 meter).
- Remote (REM) Connection: Connect a remote turn-on wire (e.g., 18-gauge) from the amplifier's REM terminal to the remote output of your head unit. This wire turns the ampپنهنجي هيڊ يونٽ سان لائفائر کي آن ۽ آف ڪريو.
- آر سي اي ان پٽ ڪنيڪشن: آر سي اي ڪيبلز کي پري کان ڳنڍيو.amp outputs of your head unit to the RCA inputs on the ampوierيڪ زنده
- اسپيڪر آئوٽ پٽ ڪنيڪشن: پنھنجي سب ووفر کي سان ڳنڍيو amplifier's speaker terminals. Pay close attention to polarity (+ to + and - to -). For multiple subwoofers, ensure proper wiring for the desired impedance load.
5. هلائڻ Ampزندگي گذاريندڙ
5.1 Initial Power-Up:
Once all connections are made and double-checked, reconnect the vehicle's battery. Turn on your head unit. The amplifier's "Power" indicator light should illuminate, indicating it is receiving power and is operational. If the "Protect" light illuminates, refer to the Troubleshooting section.
5.2 Adjusting Controls:
- گينڊي ڪنٽرول: This is not a volume control. It matches the ampآئوٽ پُٽ واليم ڏانهن لائفائر جي ان پٽ حساسيتtage of your head unit. Start with the gain set to minimum. Play a familiar track with a strong bass signal at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back off slightly.
- گھٽ پاس فلٽر (LPF): Adjust this control to filter out frequencies above the desired range for your subwoofer. A common starting point is between 80Hz and 120Hz, depending on your subwoofer and other speakers.
- پرش ترقيء: Use this control sparingly. Excessive bass boost can lead to distortion and potential damage to your subwoofer. Start at minimum and increase only if more bass impact is desired, ensuring the sound remains clean.
6. سار سنڀال
باقاعده سار سنڀال توهان جي ڊگهي عمر ۽ ڪارڪردگي کي يقيني بڻائڻ ۾ مدد ڪري ٿي ampوierيڪ زنده
- صفائي: وقتي طور تي صاف ڪريو amplifier's exterior with a soft, dry cloth to remove dust and dirt. Do not use harsh chemicals or abrasive cleaners. Ensure the cooling fins are free of obstructions.
- ڪنيڪشن چيڪ: Occasionally inspect all wiring connections (power, ground, remote, RCA, speaker) to ensure they are secure and free from corrosion. Loose connections can cause performance issues or damage.
- وينٽيليشن: کي يقيني بڻايو amplifier's mounting location remains well-ventilated. Clear any objects that might obstruct airflow around the unit.
7. مسئلا حل ڪرڻ
جيڪڏهن توهان کي مشڪلاتن جو تجربو آهي ampلائفائر، ٽيڪنيڪل سپورٽ سان رابطو ڪرڻ کان اڳ هيٺ ڏنل جدول سان صلاح ڪريو.
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| بجلي ناهي (پاور ايل اي ڊي بند) | Blown fuse; Loose power/ground/remote connection; Faulty wiring. | چيڪ ڪريو amplifier fuse and in-line battery fuse. Verify all power, ground, and remote connections are secure and have proper voltage. |
| ايل اي ڊي آن کي محفوظ ڪريو | Overheating; Speaker short circuit; Low impedance load; DC offset. | اجازت ڏيو amplifier to cool down. Check speaker wiring for shorts. Verify speaker impedance matches amplifier's minimum rating. Disconnect RCA inputs to check for DC offset. |
| ڪوبه آواز آئوٽ | No input signal; Gain set too low; Speaker wires disconnected/shorted; Head unit settings. | Check RCA connections from head unit. Increase gain. Inspect speaker wiring. Ensure head unit's subwoofer output is enabled and volume is up. |
| بگڙيل آواز | Gain set too high; Improper LPF setting; Poor ground connection; Damaged speaker. | Reduce gain. Adjust LPF. Check ground connection for cleanliness and security. Inspect speaker for damage. |
8. وضاحتون
The following are the general specifications for the Lanzar Max Pro 1800 Watt Mono Block Amplifier (Model MAXP1200):
| خاصيت | تفصيل |
|---|---|
| برانڊ | لانچ |
| ماڊل نمبر | MAXP1200 |
| پيداوار جي ماپ (L x W x H) | 38.1 x 32.2 x 11.1 سينٽي ميٽر (15 x 12.67 x 4.38 انچ) |
| شيءِ جو وزن | 3.98 ڪلوگرام (8.77 پائونڊ) |
| چڙهڻ جو قسم | مٿاڇري جبل |
| ٺاهيندڙ | Xtensive Car Audio |
| ASIN | B003OUI5VO |
| يو پي سي | 068888899864 |
نوٽ: پراڊڪٽ جي بهتري لاءِ وضاحتون بغير اطلاع جي تبديل ٿي سگهن ٿيون.
9. وارنٽي ۽ سپورٽ
Lanzar products are designed and manufactured to the highest quality standards. For information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or visit the official Lanzar webسائيٽ.
For technical assistance, troubleshooting beyond this manual, or service inquiries, please contact Lanzar customer support. Contact information can typically be found on the product packaging or the official Lanzar website. Please have your model number (MAXP1200) and purchase details ready when contacting support.
