سيلي SA686 ايئر امپڪٽ رنچ يوزر مينوئل

تعارف

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Sealey SA686 Air Impact Wrench. The SA686 is a 1" Sq Drive Compact Air Impact Wrench featuring a Twin Hammer mechanism, designed for heavy-duty fastening and loosening applications. Please read this manual thoroughly before using the tool to ensure proper handling and to prevent injury or damage.

Figure 1: The Sealey SA686 Air Impact Wrench, showcasing its compact design and 1-inch square drive.

حفاظت جي ڄاڻ

Always observe the following safety precautions to reduce the risk of personal injury or damage to the tool.

• ذاتي حفاظتي سامان: Always wear approved eye protection (safety glasses or goggles) and hearing protection (earplugs or earmuffs) when operating the impact wrench. Gloves are also recommended.
• هوا جي فراهمي: Ensure the air compressor is capable of providing the required air pressure and volume. Do not exceed the maximum operating pressure of the tool. Use clean, dry, regulated compressed air.
• نلي ۽ ڪنيڪشن: Inspect air hoses for wear, cuts, or damage before each use. Ensure all connections are secure to prevent accidental disconnection.
• ڪم جو علائقو: ڪم واري علائقي کي صاف، چڱي طرح روشن، ۽ رڪاوٽن کان پاڪ رکو. مناسب وينٽيليشن کي يقيني بڻايو.
• محفوظ ورڪ پيس: آپريشن دوران حرڪت کي روڪڻ لاءِ هميشه ورڪ پيس کي محفوظ ڪريو.
• صحيح گرفت: Maintain a firm grip on the tool at all times. Be prepared for torque reaction.
• حادثاتي شروعات کان بچو: Ensure the trigger is not depressed when connecting to the air supply or changing accessories.
• سار سنڀال: Disconnect the tool from the air supply before performing any maintenance, changing accessories, or storing the tool.
• اوزار جي حالت: Do not use the tool if it is damaged or malfunctioning. Refer to the troubleshooting section or contact qualified service personnel.
• ٻار ۽ تماشائي: ٻارن ۽ مسافرن کي آپريٽنگ ايريا کان پري رکو.

سيٽ اپ ڪريو

1. پيڪنگ کولڻ: Carefully remove the impact wrench from its packaging. Inspect the tool for any signs of shipping damage. Report any damage to your supplier immediately.
2. ايئر سپلائي ڪنيڪشن:
   • پڪ ڪريو ته توهان جو ايئر ڪمپريسر بند آهي ۽ دٻاءُ گهٽجي ويو آهي.
   • Connect a suitable air hose (minimum 3/8" I.D. recommended for optimal performance) to the air inlet of the impact wrench. The air inlet is typically located at the base of the handle.
   • Install an in-line air filter/lubricator unit as close to the tool as possible. This helps to ensure clean, lubricated air, which is crucial for the tool's longevity.
   • Set the air pressure regulator on your compressor to the recommended operating pressure (refer to Specifications section).
3. لوڻ: Before first use and regularly thereafter, add a few drops of air tool oil into the air inlet. This lubricates the internal components.
4. ساکٽ اٽيچمينٽ:
   • Select the correct 1" square drive impact socket for your application. Only use impact-grade sockets.
   • Push the socket firmly onto the square drive anvil until it clicks into place or is securely seated.

آپريٽنگ هدايتون

Follow these steps for effective and safe operation of your SA686 Air Impact Wrench.

1. ھدايت ڪنٽرول: Locate the forward/reverse selector switch, typically near the trigger or at the rear of the tool. Set it to the desired direction (forward for tightening, reverse for loosening).
2. Applying the Tool: Place the impact socket squarely onto the fastener (nut or bolt head). Ensure the socket is fully engaged.
3. اوزار کي چالو ڪرڻ: Depress the trigger to start the tool. The tool will begin to impact, applying torque to the fastener.
4. ڪنٽرولنگ ٽورڪ: The SA686 is a powerful tool. For critical torque applications, always use a calibrated torque wrench for final tightening or to verify torque after using the impact wrench. Avoid over-tightening fasteners.
5. Loosening Fasteners: For stubborn fasteners, apply steady pressure and allow the tool to impact until the fastener begins to turn.

Figure 2: The SA686 in use, demonstrating its application on large industrial fasteners. Note the user's firm grip and protective gloves.

شڪل 3: هڪ پاسو view of the impact wrench in operation, highlighting the extended anvil and the connection to the air hose.

Figure 4: A closer look at the user's hands on the tool, showing the ergonomic handle and trigger mechanism during use.

سار سنڀال

Regular maintenance ensures the longevity and optimal performance of your air impact wrench.

• روزاني لوبريڪيشن: Before each use, or at the start of each shift, add 5-10 drops of high-quality air tool oil into the air inlet. Run the tool for a few seconds to distribute the oil.
• Air Filter/Lubricator: Regularly check and drain any moisture from the air filter. Ensure the lubricator reservoir is filled with appropriate air tool oil.
• صفائي: Keep the tool clean and free from dirt, dust, and debris. Wipe down the exterior with a clean cloth. Do not use harsh solvents.
• Anvil Inspection: Periodically inspect the square drive anvil for wear or damage. Replace if necessary.
• نلي ۽ فٽنگ: Check air hoses and fittings for leaks, wear, or damage. Replace any compromised components.
• اسٽوريج: When not in use, disconnect the tool from the air supply. Store the tool in a clean, dry, and secure location, away from extreme temperatures and corrosive environments.

مشڪلاتون

This section addresses common issues you might encounter with your SA686 Air Impact Wrench.

If the problem persists after attempting these solutions, discontinue use and contact Sealey customer support or a qualified service center.

وضاحتون

وارنٽي ۽ سپورٽ

For warranty information, please refer to the warranty card included with your product or visit the official Sealey webسائيٽ. وارنٽي جون شرطون ۽ ضابطا علائقي ۽ پيداوار جي لحاظ کان مختلف ٿي سگهن ٿا.

If you require technical assistance, spare parts, or service for your Sealey SA686 Air Impact Wrench, please contact Sealey customer support directly. Contact details can typically be found on the Sealey webسائيٽ تي يا توهان جي پراڊڪٽ پيڪنگنگ تي.

نوٽ: Unauthorized repairs or modifications will void the product warranty.