Ampروب AM-570 انڊسٽريل ڊجيٽل ملٽي ميٽر يوزر مينوئل

1. تعارف

This manual provides essential instructions for the safe and effective operation of the Amprobe AM-570 Industrial Digital Multimeter. The AM-570 is designed for professionals requiring accurate and reliable measurements in various electrical, HVAC/R, and industrial maintenance applications. Please read this manual thoroughly before using the device to ensure proper function and safety.

2. حفاظت جي ڄاڻ

To prevent electric shock or personal injury, and to avoid damage to the meter or the equipment under test, observe the following safety guidelines:

• هميشه مقامي ۽ قومي حفاظتي ضابطن تي عمل ڪريو.
• جي Amprobe AM-570 is rated for CAT IV 600 V and CAT III 1000 V. Do not exceed these ratings.
• Inspect test leads for damaged insulation or exposed metal before use. Replace damaged leads immediately.
• Ensure the function switch is in the correct position for the measurement being performed.
• درجه بندي واري حجم کان وڌيڪ لاڳو نه ڪريوtage between terminals or between any terminal and ground.
• وول سان ڪم ڪرڻ وقت احتياط استعمال ڪريوtages above 30 V AC RMS, 42 V peak, or 60 V DC. These voltagاهو هڪ جھٽڪو جو خطرو آهي.
• سرڪٽ کي بجلي بند ڪريو ۽ سڀ هاءِ وولٽ ڊسچارج ڪريوtage capacitors before performing resistance, continuity, diode, or capacitance tests.
• جيڪڏهن ميٽر خراب نظر اچي يا صحيح طرح ڪم نه ڪري رهيو هجي ته ان کي نه هلايو.
• Replace the battery as soon as the low battery indicator appears to ensure accurate readings.
• جڏهن ميٽر جي خدمت ڪريو، صرف مخصوص متبادل حصن کي استعمال ڪريو.

3. پيڪيج مواد

Verify that all items listed below are present and undamaged:

• Amprobe AM-570 Industrial Digital Multimeter
• Test Leads (one pair, red and black)
• K-Type Thermocouple Probes (two)
• کڻڻ وارو ڪيس
• 9V بيٽري (اڳ ۾ نصب ٿيل يا الڳ الڳ شامل)
• استعمال ڪندڙ جو دستياب (ھي دستاويز)

تصوير 3.1: دي Amprobe AM-570 Digital Multimeter shown with its standard accessories, including test leads, two K-type thermocouple probes, and a soft carrying case.

4. مصنوعات جون خاصيتون

جي Amprobe AM-570 offers a comprehensive set of features for diverse electrical measurements:

• ماپون AC/DC Voltage 1000 V تائين
• Measures AC/DC Current
• Measures Resistance, Frequency, Capacitance, and Temperature
• Measures Duty Cycle
• True-RMS technology for accurate readings in non-linear loads
• Low Z mode to detect stray voltages and eliminate ghost readings
• Low Pass Filter for accurate voltage measurements on variable frequency drives (VFDs)
• غير رابطي وارو جلدtage (NCV) detection for quick voltage presence checks
• Built-in flashlight for illumination in dimly lit areas
• Data Hold, MAX/MIN, and Peak Hold functions
• CAT IV 600 V / CAT III 1000 V safety rating

تصوير 4.1: دي Amprobe AM-570 Digital Multimeter, showing its display, rotary dial, and function buttons. The display indicates a DC voltage reading of 119.4 V.

تصوير 4.2: هڪ زاويه view جو Amprobe AM-570 Digital Multimeter, highlighting the clear digital display, which currently shows a frequency reading of 0.000 kHz.

5. سيٽ اپ

5.1 بيٽري لڳائڻ

1. پڪ ڪريو ته ميٽر بند آهي.
2. ميٽر جي پوئين پاسي بيٽري جي خاني کي ڳوليو.
3. بيٽري جي ڍڪ کي محفوظ ڪرڻ واري اسڪرو کي کولڻ لاءِ اسڪرو ڊرايور استعمال ڪريو.
4. بيٽري جو ڍڪ هٽايو.
5. Insert a new 9V battery, observing correct polarity.
6. بيٽري جي ڍڪ کي تبديل ڪريو ۽ ان کي اسڪرو سان محفوظ ڪريو.

5.2 ٽيسٽ ليڊز کي ڳنڍڻ

Always connect the black test lead to the COM (common) terminal. Connect the red test lead to the appropriate input terminal based on the measurement function:

• VΩHz: For voltage, resistance, frequency, capacitance, and diode/continuity measurements.
• mAµA: For milliampاڳ ۽ مائڪروampere current measurements.
• 10A: For high current (up to 10A) measurements.

تصوير 5.1: دي Amprobe AM-570 Digital Multimeter shown with its integrated kickstand extended, allowing for hands-free viewآپريشن دوران.

6. آپريٽنگ هدايتون

The AM-570 features a rotary dial for selecting primary measurement functions and push buttons for secondary functions and settings.

6.1 فنڪشن جي چونڊ

Turn the rotary dial to the desired measurement function. Use the چونڊيو button to toggle between primary and secondary functions within a single dial position (e.g., AC/DC voltagاي، مزاحمت/ تسلسل/ ڊائيوڊ).

6.2 ماپ جا ڪم

• جلدtage (V~ / V--): Select the V~ (AC) or V-- (DC) position. Connect test leads in parallel with the circuit.
• Current (10A / mAµA): Select the 10A or mAµA position. Connect the meter in series with the circuit. Ensure correct terminal connection.
• مزاحمت (Ω): Select the Ω position. Ensure power is off and capacitors are discharged. Connect test leads across the component.
• Continuity ())): Select the Ω position and press چونڊيو until the continuity symbol appears. A continuous beep indicates continuity.
• Diode Test (→|): Select the Ω position and press چونڊيو until the diode symbol appears. Connect leads across the diode.
• گنجائش (F): Select the F position. Ensure power is off and capacitors are discharged. Connect leads across the capacitor.
• Frequency (Hz) / Duty Cycle (%): Select the Hz% position. Connect leads to the signal source. Press چونڊيو to toggle between frequency and duty cycle.
• درجه حرارت (° C / ° F): Select the TEMP °C/°F position. Insert K-type thermocouple probes into the T1 and T2 inputs. Press چونڊيو to toggle between Celsius and Fahrenheit.
• غير رابطي وارو جلدtage (NCV): Select the NCV position. Hold the top of the meter near a live conductor. The NCV indicator and audible alarm will activate if voltage جو پتو لڳايو ويو آهي.
• Low Z Mode: Select the LoZ V~ position for AC voltage measurements with low impedance. This helps to eliminate ghost voltages.
• گھٽ پاس فلٽر: Activated automatically in certain AC voltage modes, this filter allows for accurate measurements on variable frequency drives.

6.3 خاص ڪم

• RANGE: Manually select the measurement range instead of auto-ranging.
• REL (Relative Mode): Measures the difference between a stored reference value and the current reading.
• MAX/MIN: Records the maximum and minimum values over a measurement period.
• رکو: Freezes the current display reading.
• PEAK (1ms): Captures fast transient peaks (positive and negative) with a 1ms response time.

Image 6.1: An electrician utilizing the Amprobe AM-570 Digital Multimeter to perform voltage measurements within an industrial electrical panel, demonstrating practical application.

7. سار سنڀال

7.1 صفائي

ميٽر کي اشتهار سان صاف ڪريوamp cloth and mild detergent. Do not use abrasives or solvents. Ensure the meter is dry before use.

7.2 بيٽري مٽائڻ

Refer to Section 5.1 for detailed instructions on replacing the 9V battery. Replace the battery promptly when the low battery indicator appears on the display.

7.3 فيوز مٽائڻ

If the current measurement functions cease to operate, the internal fuses may need replacement. Fuse replacement should only be performed by qualified personnel. Refer to the full service manual for fuse specifications and replacement procedures. Always use fuses with the specified voltagاي ۽ موجوده درجه بندي.

7.4 اسٽوريج

When not in use for extended periods, remove the battery to prevent leakage. Store the meter in a cool, dry environment, preferably in its carrying case.

8. مسئلا حل ڪرڻ

9. وضاحتون

10. وارنٽي ۽ سپورٽ

Amprobe products are designed for reliability and performance. This product is covered by a manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official Ampچادر webسائيٽ.

For technical support, service, or replacement parts, please contact Amprobe customer service. Contact information can typically be found on the Ampچادر webسائيٽ يا پيداوار جي پيڪنگنگ ۾.