Behringer EUROLIVE VQ1800D ايڪٽو پي اي سب ووفر هدايت نامو

1. تعارف

This manual provides essential information for the safe and efficient operation of your Behringer EUROLIVE VQ1800D Active PA Subwoofer. Please read this manual thoroughly before operating the device to ensure proper setup, usage, and maintenance. Retain this manual for future reference.

تصوير 1.1: سامهون view of the Behringer EUROLIVE VQ1800D Active PA Subwoofer.

2. حفاظتي هدايتون

بجليءَ جي جھٽڪي، باهه، يا زخم جي خطري کي گهٽائڻ لاءِ هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:

• بجلي جي فراهمي: ڊوائيس کي ڳنڍيو صرف مينز وال سانtage specified on the unit. Ensure the power cable is not damaged and is routed safely to prevent tripping hazards.
• وينٽيليشن: Do not block ventilation openings. Install the device in a location with adequate airflow to prevent overheating.
• نمي ۽ گرمي: Do not expose the device to rain, moisture, dripping or splashing liquids. Keep away from direct heat sources or extreme temperatures.
• لڳائڻ: Place the subwoofer on a stable, level surface. Avoid placing it in direct sunlight or near strong magnetic fields.
• ٻڌڻ جي حفاظت: Prolonged exposure to high sound pressure levels can cause permanent hearing damage. Use appropriate hearing protection when operating the subwoofer at high volumes.
• خدمت ڪرڻ: Do not attempt to service this device yourself. Refer all servicing to qualified service personnel.

3. پيڪيج مواد

پيڪنگ ڪرڻ وقت پڪ ڪريو ته سڀئي شيون موجود آهن:

• 1 x Behringer EUROLIVE VQ1800D Active PA Subwoofer
• 1 x پاور ڪيبل
• هدايت نامو (هي دستاويز)

4. سيٽ اپ

Follow these steps for initial setup of your subwoofer:

4.1. جسماني جڳهه

Position the VQ1800D subwoofer on a stable, flat surface, preferably on the floor, to maximize bass response. Ensure there is adequate space around the unit for ventilation.

تصوير 4.1: اڳوڻيample setup with the VQ1800D subwoofer and full-range speakers.

4.2. ڪنيڪشن

The VQ1800D features a built-in stereo crossover, allowing you to connect full-range loudspeakers directly to its outputs.

1. پاور ڪنيڪشن: Connect the supplied power cable to the AC inlet on the rear panel of the subwoofer and then to a suitable mains power outlet.
2. آڊيو ان پٽ: Connect your audio source (e.g., mixer, audio interface) to the XLR input connectors (INPUT 1 or INPUT 2) on the rear panel.
3. Audio Output (to Full-Range Speakers): If using the built-in stereo crossover, connect your full-range loudspeakers to the XLR output connectors (OUTPUT 1 or OUTPUT 2). These outputs provide a high-pass filtered signal to your main speakers, optimizing their performance.

Image 4.2: Rear panel showing input/output connections and controls.

5. آپريٽنگ هدايتون

5.1. پاور آن/آف

1. پڪ ڪريو ته سڀئي ڪنيڪشن محفوظ آهن پاور آن ڪرڻ کان پهريان.
2. Press the POWER switch on the rear panel to turn the subwoofer on. The power LED will illuminate.
3. To power off, press the POWER switch again.

5.2. Adjusting Volume and Crossover

The VQ1800D features controls for fine-tuning its performance:

• ليول ڪنٽرول: Adjusts the overall output volume of the subwoofer. Start with a low setting and gradually increase to your desired level.
• BOOST Frequency: Allows you to select a specific frequency range (40 Hz to 90 Hz) to boost for enhanced bass impact.
• HIGH CUT Control: Sets the crossover frequency for the subwoofer (70 Hz to 150 Hz). This determines the upper frequency limit of the subwoofer's output and the lower frequency limit of the signal sent to your full-range speakers via the 'PASS THRU' outputs.
• فيز سوئچ: Inverts the phase of the subwoofer's output. Experiment with this setting to achieve optimal bass alignment with your main speakers.
• LED جي حد: Illuminates when the internal limiter is active, indicating that the signal is too high and clipping may occur. Reduce the input level or the LEVEL control if this LED is constantly lit.

تصوير 5.1: تفصيلي view of the control panel for volume, boost, and crossover settings.

6. سار سنڀال

باقاعده سار سنڀال توهان جي سب ووفر جي ڊگهي عمر ۽ بهترين ڪارڪردگي کي يقيني بڻائي ٿي:

• صفائي: Use a soft, dry cloth to clean the exterior of the subwoofer. Do not use abrasive cleaners or solvents.
• وينٽيليشن: Periodically check that the ventilation openings are free from dust and debris.
• اسٽوريج: When not in use for extended periods, store the subwoofer in a dry, cool environment, protected from dust and extreme temperatures.
• چڪاس: Regularly inspect the power cable and audio cables for any signs of damage. Replace damaged cables immediately.

7. مسئلا حل ڪرڻ

If you encounter issues with your VQ1800D subwoofer, refer to the following common troubleshooting steps:

• طاقت ناهي: Ensure the power cable is securely connected to both the subwoofer and the power outlet. Check the power switch position and the mains fuse.
• آواز ناهي: Verify that the audio source is active and connected correctly to the subwoofer's inputs. Check the LEVEL control setting. Ensure any connected full-range speakers are also powered on and receiving a signal from the subwoofer's outputs.
• Distorted Sound / LIMIT LED Constantly On: Reduce the input signal level from your audio source or lower the subwoofer's LEVEL control. The LIMIT LED indicates that the amplifier is being overdriven.
• ڪمزور بيس: Check the PHASE switch setting. Experiment with both positions to find the optimal phase alignment with your main speakers. Ensure the HIGH CUT frequency is set appropriately for your system.

If the problem persists after attempting these steps, contact qualified service personnel.

8. وضاحتون

9. وارنٽي ۽ سپورٽ

The Behringer EUROLIVE VQ1800D Active PA Subwoofer comes with a limited warranty. For detailed warranty information, product registration, and technical support, please visit the official Behringer webسائيٽ تي وڃو يا پنهنجي مقامي ورهائيندڙ سان رابطو ڪريو.

For further assistance, refer to the contact information provided on the product packaging or the official Behringer support channels.