CDVI 433MHz Radio Keypad and Receiver User Manual

1. تعارف

This manual provides detailed instructions for the installation, operation, and maintenance of the CDVI 433MHz Radio Keypad (Digicode) and its associated SEL2641R433NN 1-Relay 12V Receiver. This system is designed for secure access control applications.

Please read this manual thoroughly before attempting any installation or operation to ensure proper functionality and safety.

Figure 1: CDVI 433MHz Radio Keypad and SEL2641R433NN Receiver. The image shows the silver-colored keypad with illuminated blue numbers (0-9, A, B, C) and a transparent plastic receiver unit.

2. حفاظت جي ڄاڻ

• Ensure all power is disconnected before installation or maintenance.
• تنصيب صرف قابل عملدار طرفان ڪيو وڃي.
• Do not expose the keypad or receiver to extreme temperatures, moisture, or direct sunlight.
• Use only specified power supply (12V).
• ٻارن جي پهچ کان پري رکو.

3. سيٽ اپ ۽ تنصيب

3.1. اجزاء اوورview

The system consists of two main components:

• Radio Keypad (Digicode): The input device for entering access codes.
• SEL2641R433NN Receiver: The unit that receives signals from the keypad and controls the access mechanism (e.g., door lock).

3.2. ڪي پيڊ تي چڙهڻ

1. Choose a suitable mounting location, typically near the access point, ensuring it is protected from direct weather exposure if outdoors.
2. Mark the drilling points using the keypad's mounting plate as a template.
3. سوراخ ڪريو ۽ مناسب وال پلگ لڳايو.
4. ڀت تي چڙهڻ واري پليٽ کي محفوظ ڪريو.
5. Attach the keypad securely to the mounting plate.

3.3. Wiring the Receiver

The SEL2641R433NN receiver requires a 12V power supply and connection to the access control device. Refer to the wiring diagram below for typical connections.

• پاور ان پٽ: Connect 12V DC to the designated terminals. Observe polarity.
• رلي جي اوٽ: The receiver has one relay. Connect the Normally Open (NO) or Normally Closed (NC) contacts to your access control device (e.g., electric strike, magnetic lock) as required.

(Note: A detailed wiring diagram is typically provided with the physical product. Consult it for specific terminal assignments.)

4. آپريٽنگ هدايتون

4.1. شروعاتي پاور اپ

Once the receiver is wired and powered, it will enter a standby mode. The keypad will illuminate when a button is pressed.

4.2. Programming Access Codes

The keypad and receiver must be paired, and access codes programmed. This process typically involves:

1. پروگرامنگ موڊ ۾ داخل ٿيڻ: This usually involves a master code or a physical button on the receiver.
2. Adding New Codes: Follow the specific sequence to input new user codes (e.g., Master Code + * + New Code + #).
3. Deleting Codes: Follow the specific sequence to remove existing user codes.
4. پروگرامنگ موڊ مان نڪرڻ: Save changes and exit programming mode.

(Note: Refer to the specific programming instructions provided with your product for exact key sequences and procedures, as these can vary by firmware version.)

4.3. Granting Access

To grant access, simply enter a valid programmed code on the keypad. Upon successful code entry, the receiver's relay will activate for a pre-set duration, unlocking the connected device.

5. سار سنڀال

• صفائي: ڪي پيڊ جي مٿاڇري کي نرم، ڊي سان صاف ڪريوamp ڪپڙو. استعمال نه ڪريو abrasive cleaners يا solvents.
• باقاعده چڪاس: Periodically check all wiring connections for security and integrity, especially for the receiver unit.
• ڪوڊ مينيجمينٽ: باقاعده ٻيهرview and update access codes for security purposes. Delete codes of former users.

6. مسئلا حل ڪرڻ

7. وضاحتون

8. وارنٽي ۽ سپورٽ

Information regarding product warranty is typically provided with the purchase documentation or can be found on the manufacturer's official webسائيٽ. مھرباني ڪري وارنٽي دعوائن لاءِ خريداري جو ثبوت رکو.

For technical support or further assistance, please contact CDVI customer service or your authorized dealer. Contact details can usually be found on the CDVI webسائيٽ (www.cdvi.com).