TRIGGER 4 Plus Wireless Accessory Controller (Model 2100) Instruction Manual

تعارف

The TRIGGER 4 Plus Wireless Accessory Controller (Model 2100) is designed to simplify the installation and control of your vehicle's electronic accessories. This system eliminates the need to route wires through the firewall or under the dashboard, offering wireless control via an RF remote and a Bluetooth-enabled mobile application.

اهم خاصيتون شامل آهن:

• Wireless control for up to four accessories.
• RF remote control for activation outside the vehicle.
• Bluetooth app for on/off, dimming, and flashing functions.
• Fused circuits with LED indicators for blown fuses.
• Accepts 12-24 Volt input.
• ٻه 30 Amp and two 10 Amp fused circuits with 12-24 Volt output.
• Includes 4 wire harnesses with waterproof connectors.

پيڪيج مواد

پڪ ڪريو ته سڀئي جزا توهان جي پيڪيج ۾ موجود آهن:

• TRIGGER 4 Plus Control Box
• Wireless Backlit RF Remote Rocker Switch Module
• Four (4) Wire Harnesses with Waterproof Connectors (two 30A, two 10A)
• Main Power Input Wires (Red, Yellow, Black)
• Assorted Electrical Connectors and Zip Ties
• Accessory Identification Stickers

سيٽ اپ ۽ تنصيب

1. ڪنٽرول باڪس تي چڙهڻ

   Select a secure, dry location under the hood of your vehicle for the TRIGGER 4 Plus Control Box. Ensure it is away from excessive heat and moving parts. The unit features a magnetic mount for easy placement, or it can be secured using screws through the mounting tabs.

   

2. وائرنگ ڪنٽرول باڪس

   • ڳاڙهو تار: Connect directly to the positive (+) terminal of your vehicle's battery.
   • ڪارو تار: Connect directly to a reliable chassis ground point on your vehicle.
   • زرد تار: Connect to an ignition-switched 12V source. This can be done using a fuse tap (not included) on an ignition-only fuse in your vehicle's fuse box. This ensures the unit powers off with the vehicle to prevent battery drain.

   Warning: Ensure all connections are secure and properly insulated to prevent short circuits.

3. ڳن Accessoriesيل لوازمات

   Connect your 12V accessories to the provided wire harnesses. The TRIGGER 4 Plus has four output circuits: two 30 Amp and two 10 Amp. Match the accessory's current draw to the appropriate circuit.

   

   • Each harness has a waterproof connector that plugs into the corresponding port on the control box.
   • Route accessory wires neatly and secure them to prevent damage.

4. Installing the RF Remote

   The wireless RF remote module can be mounted on flat or round surfaces using its universal mounting system. It is battery-powered and backlit for visibility.

   

   • Install the required batteries (type specified in remote documentation, typically coin cell).
   • Mount the remote in an easily accessible location within the vehicle.

آپريٽنگ هدايتون

Using the RF Remote

Press the corresponding button on the RF remote to activate or deactivate an accessory. The buttons are backlit and provide tactile feedback.

Using the Mobile App (Bluetooth)

1. Download the "TRIGGER ACS PLUS" app from your device's app store (iOS or Android).
2. پڪ ڪريو ته توهان جي موبائل ڊوائيس تي بلوٽوت فعال آهي.
3. Open the app and follow the on-screen instructions to pair with your TRIGGER 4 Plus unit.
4. Once paired, you can control on/off functions, dimming (for compatible lighting), and flashing modes directly from your phone.

دستي ڪنٽرول

The control box itself has manual buttons (1-4) for individual circuit power. These can be used to activate accessories directly at the unit.

سار سنڀال

• فيوز مٽائڻ: The control box features LED indicators that illuminate when a fuse is blown. To replace a fuse, carefully remove the transparent cover, replace the blown fuse with one of the same amperage rating (30A or 10A), and re-secure the cover.
• Battery Replacement (RF Remote): When the remote's backlight dims or it becomes unresponsive, replace its internal batteries. Refer to the remote's specific instructions for battery type and replacement procedure.
• ڪنيڪشن چيڪ: Periodically inspect all wiring connections for corrosion or looseness. Ensure waterproof connectors are properly seated.
• صفائي: Keep the control box and remote free of excessive dirt and debris. Use a damp صفائي لاءِ ڪپڙو؛ سخت ڪيميڪلز کان پاسو ڪريو.

مشڪلاتون

• يونٽ پاور نه آهي:
  • Check the main power (red wire) and ground (black wire) connections for secure contact.
  • Verify the ignition wire (yellow wire) is connected to a live 12V source when the ignition is on.
  • Inspect the main fuse (if applicable) on the red power wire.
• Accessory Not Activating:
  • Check the LED indicator on the control box for the specific circuit. If lit, the fuse is blown and needs replacement.
  • Ensure the accessory is properly connected to its harness and the harness is securely plugged into the control box.
  • Verify the accessory itself is functioning correctly by testing it independently.
• RF Remote Unresponsive:
  • Replace the batteries in the RF remote.
  • Ensure the remote is within range of the control box (up to 30ft).
  • If multiple TRIGGER units are present, ensure the remote is paired to the correct unit (refer to pairing instructions in the full manual, if available).
• Bluetooth App Connectivity Issues:
  • پڪ ڪريو ته توهان جي موبائل ڊوائيس تي بلوٽوت فعال آهي.
  • Restart the app and attempt to reconnect.
  • Ensure no other devices are actively connected to the TRIGGER unit via Bluetooth.
  • If issues persist, try unpairing and re-pairing the device in your phone's Bluetooth settings.
• گھٽ وولٽtagاي ڪٽ آف:

  The system includes a low voltage cut-off feature to protect your vehicle's battery. If the battery voltage drops too low, the unit will shut down. Recharge your vehicle's battery if this occurs.

وضاحتون

وارنٽي ڄاڻ

The TRIGGER 4 Plus Wireless Accessory Controller comes with a 3-سال وارنٽي. For warranty claims or detailed terms and conditions, please refer to the official TRIGGER product webسائيٽ يا ڪسٽمر سپورٽ سان رابطو ڪريو.

حمايت

For technical assistance, troubleshooting not covered in this manual, or further inquiries, please contact TRIGGER customer support. Contact information can typically be found on the manufacturer's webسائيٽ يا پراڊڪٽ پيڪنگنگ.

آن لائن وسيلن ۾ شامل ٿي سگھي ٿو:

• Official TRIGGER Webسائيٽ
• Product FAQs and support documents.