UHPPOTE TK4100 125kHz RFID ڪي فوب استعمال ڪندڙ دستياب

1. تعارف

This manual provides essential information for the proper use, setup, and maintenance of your UHPPOTE TK4100 125kHz RFID Key Fobs. Please read these instructions carefully to ensure optimal performance and compatibility with your access control systems.

2. پراڊڪٽ ختمview

The UHPPOTE TK4100 125kHz RFID Key Fobs are designed for various access control and identification applications. These key fobs are read-only and cannot be reprogrammed. Each fob is pre-programmed with a unique ID number.

Image 1: A collection of blue UHPPOTE TK4100 125kHz RFID key fobs, each equipped with a metal key ring, ready for use in access control systems.

اهم خاصيتون:

• صرف پڙهو: These key fobs are pre-programmed and cannot be altered.
• Standard EM Card Type: Compatible with standard EM ID access devices and readers.
• TK4100 Chip: Utilizes the TK4100 chip for 125kHz RFID communication.
• رابطي کان سواءِ آپريشن: Data and energy transmission occur without physical contact.
• پائيدار تعمير: Made from waterproof and durable ABS material.
• منفرد سڃاڻپ: Each fob has a unique, pre-programmed ID number, with the first 10 digits often printed on the card.
• فاصلو معلوم ڪرڻ: Effective reading range of approximately 1-10mm (3/64"-25/64").
• درخواستون: Suitable for access control, attendance tracking, hotel locks, staff management, school campus access, and membership systems.

تصوير 2: هڪ تفصيلي view of two UHPPOTE TK4100 125kHz RFID key fobs, highlighting the printed unique identification number on one of the fobs.

3. سيٽ اپ

To integrate your UHPPOTE TK4100 Key Fobs into an access control system, follow the instructions provided with your specific RFID reader or access control panel.

Key Fob Registration:

1. Identify the Key Fob ID: Each key fob is pre-programmed with a unique ID number. While some fobs may have a number printed on them, it is crucial to use the ID number read directly by your RFID reader or access control software for registration. The printed number may not always match the actual ID transmitted by the chip.
2. Enroll in Access System: Use your access control system's interface or software to enroll the unique ID of each key fob. Refer to your access control system's manual for specific steps on adding new credentials.
3. ٽيسٽ ڪارڪردگي: After registration, test each key fob with the reader to ensure it grants access as intended.

4. آپريٽنگ هدايتون

Using the UHPPOTE TK4100 Key Fob is straightforward:

1. Present the Key Fob: Hold the key fob within the detection range of a compatible 125kHz RFID reader. The typical detection distance is 1-10mm.
2. تصديق جو انتظار ڪريو: The reader will typically provide an audible beep or visual indicator (e.g., LED light change) to confirm successful reading of the key fob's ID.
3. Access Granted/Denied: Based on the access control system's programming, access will either be granted or denied.

5. سار سنڀال

The UHPPOTE TK4100 Key Fobs are designed for durability and require minimal maintenance.

• صفائي: If necessary, wipe the key fobs with a soft, damp ڪپڙو. سخت ڪيميڪلز يا رگڙيندڙ مواد کان پاسو ڪريو.
• اسٽوريج: Store key fobs in a cool, dry place away from direct sunlight and extreme temperatures.
• جسماني نقصان: While durable, avoid excessive force or bending, which could damage the internal chip.

6. مسئلا حل ڪرڻ

If you encounter issues with your UHPPOTE TK4100 Key Fobs, consider the following:

• Key Fob Not Detected:
  • Ensure the key fob is within the reader's detection range (1-10mm).
  • Verify that your reader operates at 125kHz and supports standard EM ID cards.
  • Confirm the key fob is not being used with an incompatible reader (see Important Compatibility Information below).
• Access Denied After Registration:
  • Double-check that the correct ID number (as read by the system, not necessarily printed on the fob) was registered in your access control system.
  • Ensure the access control system's permissions are correctly configured for the registered key fob.
  • Consult your access control system's manual or administrator.
• Intermittent Reading:
  • Ensure there are no metallic objects or other RFID devices interfering with the signal near the reader or key fob.
  • Check for any physical damage to the key fob.

7. وضاحتون

8. اهم مطابقت جي معلومات

It is critical to understand the compatibility limitations of these key fobs:

• Not Compatible with UHF Readers: These 125kHz key fobs will not work with Ultra High Frequency (UHF) RFID readers.
• Not Compatible with Encrypted Readers: The TK4100 key fobs are standard, non-encrypted cards. They are not compatible with encrypted readers from brands such as HID, Indala, Cobra, APCiK, Paradox, Radio, Honeywell, Kaba, Isonas, etc.
• Consult Your Technician: Always confirm with your access control system technician or manufacturer that your reader supports normal (non-encrypted) standard 125KHz RFID cards before purchase and implementation.

9. وارنٽي ۽ سپورٽ

Specific warranty details for the UHPPOTE TK4100 125kHz RFID Key Fobs are not provided in this manual. For warranty information, technical support, or further inquiries, please contact UHPPOTE directly or refer to their official webسائيٽ.

You can visit the official UHPPOTE store for more products and support: UHPPOTE Store