Amico 3 Head LED Security Light with Motion Sensor (Model PD-1711)

1. تعارف

This manual provides comprehensive instructions for the safe installation, operation, and maintenance of your Amico 3 Head LED Security Light with Motion Sensor. Please read this manual thoroughly before installation and retain it for future reference. Proper installation and adherence to safety guidelines are crucial for optimal performance and user safety.

حفاظت جي ڄاڻ

• انسٽاليشن يا سروسنگ کان اڳ هميشه سرڪٽ بريڪر تي بجلي بند ڪريو.
• انسٽاليشن هڪ قابل اليڪٽريشن يا پراڊڪٽ جي تعمير ۽ آپريشن ۽ ان ۾ شامل خطرن کان واقف شخص طرفان ڪئي وڃي.
• پڪ ڪريو ته سڀئي برقي ڪنيڪشن مقامي ضابطن ۽ آرڊيننس جي تعميل ڪن ٿا.
• Do not install on surfaces that are not structurally sound.
• Avoid looking directly into the LED light source when illuminated.

2. مصنوعات جون خاصيتون

The Amico 3 Head LED Security Light is designed for outdoor use, offering adjustable lighting and motion detection capabilities.

• High Brightness & Energy Efficiency: Outputs 40W, 4000 Lumens, 5000K (Daylight White) equivalent to 200W halogen light, reducing electricity consumption.
• ٽي روشني جا طريقا: Features Motion Detection, Dusk-to-Dawn (D2D), and Always-On modes for versatile operation.
• Adjustable Motion Sensor: 180-degree swiveling angle with a detection distance of up to 75 feet.
• پائيدار ۽ موسم کان بچاءُ: IP65 waterproof rating protects against rain, sleet, or snow. Constructed with aluminum for excellent heat dissipation and extended lifespan.
• ترتيب ڏيڻ وارا لائيٽ هيڊ: Three independently adjustable light heads allow for broad and customized light coverage.

3. پيڪيج مواد

انسٽاليشن شروع ڪرڻ کان اڳ پڪ ڪريو ته سڀئي جزا موجود آهن:

• Amico 3 Head LED Security Light Unit
• وڌندڙ خط
• چڙهڻ اسڪرو
• تار جا نٽ
• EVA Pad (for waterproofing)
• ھدايت وارو دستور

4. تنصيب جون هدايتون

Follow these steps for a secure and functional installation. Ensure power is OFF at the circuit breaker before starting.

1. چڙهڻ واري مٿاڇري کي تيار ڪريو: Ensure the junction box is securely installed and accessible.
2. انسٽال ڪريو ماؤنٽنگ بریکٹ: Fasten the provided mounting bracket to the existing junction box using the supplied screws. Ensure it is firmly attached.
3. Pass Wires Through EVA Pad: Carefully thread the electrical wires from the light fixture through the center hole of the EVA pad. This pad helps create a waterproof seal.
4. وائر ڪنيڪشن: Connect the wires from the light fixture to the corresponding wires from the junction box using the wire nuts.
   • Green wire (from light) to Green wire (ground from junction box)
   • Black wire (from light) to Black wire (hot from junction box)
   • White wire (from light) to White wire (neutral from junction box)

   Note: Improper wiring may cause the light to be slightly bright even when off.
5. لائيٽ فڪسچر لڳايو: Align the light fixture with the mounting bracket. Pass the screw through the hole on the light body, align with the hole in the mounting bracket, and tighten securely.
6. Seal the Hole: Block the screw hole with the provided rubber plug to maintain the light's waterproof integrity.
7. Adjust Light Heads and Sensor: Adjust the three light heads and the motion sensor to your desired angles for optimal coverage.

انسٽاليشن وڊيو گائيڊ

5. آپريٽنگ موڊس

The Amico Security Light offers three distinct operating modes, controlled by switches and dials on the motion sensor unit. Refer to the diagram below for control locations.

موڊ سيٽنگون:

• موشن ڳولڻ جو طريقو: The light activates when motion is detected within its range and turns off after a set time. Adjust the 'DISTANCE' dial to H (High), M (Medium), or L (Low) for sensitivity, and the 'TIME' dial to 1, 3, or 10 minutes for illumination duration.
• Dusk-to-Dawn (D2D) Mode: The light automatically turns on at dusk and off at dawn. To activate, set the 'DISTANCE' dial to 'D2D' and the 'TIME' dial to your desired duration (1, 3, or 10 minutes). The light will remain on for the set duration after dusk.
• هميشه آن موڊ: For continuous illumination, set the 'DISTANCE' dial to 'D2D' and the 'TIME' dial to 'TEST'. The light will remain on until manually switched off or the settings are changed. This mode can also be controlled by a wall switch.

Operating Modes Video Guide

6. سار سنڀال

Regular maintenance ensures the longevity and optimal performance of your security light.

• صفائي: Periodically clean the light heads and motion sensor lens with a soft, damp ڪپڙو. استعمال نه ڪريو abrasive cleaners يا solvents.
• چڪاس: Annually inspect the wiring and mounting for any signs of wear, damage, or loose connections. Ensure the waterproof seals are intact.
• ماحولياتي عنصر: Keep the motion sensor clear of obstructions like tree branches or debris that could interfere with its detection capabilities.

7. مسئلا حل ڪرڻ

If you encounter issues with your Amico Security Light, refer to the following common problems and solutions:

8. وضاحتون

9. وارنٽي ڄاڻ

The Amico 3 Head LED Security Light (Model PD-1711) comes with a 5-year limited warranty. For specific terms and conditions, please refer to the warranty card included in your product packaging or contact Amico customer support.

10. ڪسٽمر سپورٽ

For any questions, technical assistance, or warranty claims, please contact Amico customer support through the official Amico webسائيٽ يا توهان جي پراڊڪٽ پيڪنگنگ ۾ ڏنل رابطي جي معلومات.