1. پراڊڪٽ ختمview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. حفاظت جي ڄاڻ
هن پراڊڪٽ کي استعمال ڪرڻ وقت باهه، بجليءَ جي جھٽڪي، ۽ ذاتي زخمن جي خطري کي گهٽائڻ لاءِ هميشه بنيادي حفاظتي احتياطن تي عمل ڪريو.
- ھدايت پڙھو: Thoroughly read and understand all instructions before operating the spray gun.
- ذاتي حفاظتي سامان (PPE): Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- وينٽيليشن: Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- ٻرندڙ مواد: کليل باهه، پائلٽ لائيٽ، يا ٻين اگنيشن ذريعن جي ويجهو ٻرندڙ يا ٻرندڙ مواد جو اسپري نه ڪريو.
- برقي حفاظت: Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- ٻارن کي پري رکو: Do not allow children or untrained persons to operate the spray gun.
- محفوظ ڪنيڪشن: Ensure all air hose connections are secure before operation.
3. جزا ۽ حصا
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- ايئر انليٽ ڪنيڪٽر
شڪل 2: پاسي view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. سيٽ اپ
- پيڪ ڪريو: پيڪنگ مان سڀني حصن کي احتياط سان هٽايو. ڪنهن به نقصان جي چڪاس ڪريو.
- ايئر ڪمپريسر ڳنڍيو: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- مواد تيار ڪريو: Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- شروعاتي ترتيبون: Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. آپريٽنگ هدايتون
- Power On Compressor: Turn on your air compressor and allow it to build up sufficient pressure.
- ٽيسٽ اسپري جو نمونو: Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- اسپري ڪرڻ جي ٽيڪنڪ: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- ڀرڻ: If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. سار سنڀال
Proper cleaning and maintenance are crucial for the longevity and performance of your spray gun.
- فوري صفائي: Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- خارج ٿيڻ: Disassemble the paint pot, nozzle, and air cap.
- صفائي جا اجزاء: Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- ٻيهر گڏ ڪرڻ: Reassemble the spray gun once all parts are clean and dry.
- اسٽوريج: Store the spray gun in a clean, dry place, away from extreme temperatures and direct sunlight.
7. مسئلا حل ڪرڻ
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| ڪو به اسپري يا ڪمزور اسپري نه | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| اڻ برابر اسپري جو نمونو | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. وضاحتون
- ماڊل نالو: ASG-SFEU; EX; UK
- شئي ماڊل نمبر: 4472350
- برانڊ: اوزيٽو
- Nozzle سائيز: 1.5 ملي ميٽر
- Paint Pot Capacity: 1000 مليل
- Minimum Air Compressor Flow Rate: 85 ليٽر في منٽ
- رنگ: ڀورو
- شامل اجزاء: 1 suction spray gun
- پيڪيج جي ماپ: 28.5 x 19 x 11 سينٽي
- شيء جو وزن: 790 گرام
- ٺاهيندڙ: اين هيل
9. وارنٽي ۽ سپورٽ
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
آن لائين وسيلا: گهمڻ www.ozito.com.au (or your regional Ozito website) for product registration, FAQs, and support contact details.
