Sharp Home LED Digital Alarm Clock User Manual

1. تعارف

Thank you for choosing the Sharp Home LED Digital Alarm Clock. This clock is designed for simplicity and ease of use, featuring a large red LED display, a convenient swivel base, and essential functions like alarm, snooze, and brightness control. This manual provides instructions for setup, operation, and maintenance to ensure optimal performance of your device.

2. حفاظت جي ڄاڻ

• Read all instructions before operating the clock.
• يونٽ کي بي نقاب نه ڪريو انتهائي گرمي پد ، س sunي سج جي روشني ، مٽي ، يا نمي.
• Use only the specified power source (AC 120V outlet). Do not use with 240V.
• يونٽ کي پاڻي يا ٻين مائع کان پري رکو.
• يونٽ کي ڌار ڪرڻ يا تبديل ڪرڻ جي ڪوشش نه ڪريو. سڀني سروسنگ کي قابل اهلڪارن جي حوالي ڪريو.
• يونٽ جي چوڌاري مناسب وائيٽليشن کي يقيني بڻائي.

3. سيٽ اپ

3.1 پاور ڪنيڪشن

To power the clock, plug the power cord into a standard US 120V electrical outlet. The clock will immediately display the time.

3.2 بيٽري بيڪ اپ جي انسٽاليشن

For backup power during an outage, insert one 9V battery (not included) into the battery compartment located on the bottom of the clock. During battery backup, the display will go blank, but time and alarm settings will be retained, and the alarm will still sound at the set time.

سامهون view of the Sharp Home LED Digital Alarm Clock, displaying red LED digits on a gun metal grey case with a swivel base.

4. آپريٽنگ هدايتون

4.1 وقت مقرر ڪرڻ

1. Locate the 'TIME SET' button on the back or bottom of the clock.
2. Press and hold the 'TIME SET' button. The hour digits will begin to flash.
3. Use the 'HOUR' and 'MINUTE' buttons to adjust the time. Observe the 'PM' indicator for correct AM/PM setting.
4. Release the 'TIME SET' button to save the time.

4.2 الارم لائڻ

1. Locate the 'ALARM SET' button.
2. Press and hold the 'ALARM SET' button. The alarm hour digits will flash.
3. Use the 'HOUR' and 'MINUTE' buttons to set your desired alarm time.
4. Release the 'ALARM SET' button to save the alarm time. The 'ALM' indicator on the display will light up, indicating the alarm is active.

4.3 Alarm Volume Control

The alarm features a high/low volume setting. Refer to the controls on the back or side of the clock to adjust the alarm volume to your preference.

4.4 اسنوز فنڪشن

When the alarm sounds, press the 'SNOOZE' button (usually a large button on top) to temporarily silence the alarm for approximately 9 minutes. You can press the snooze button repeatedly until the alarm is manually switched off.

4.5 Display Brightness Dimmer

The clock features a high/low brightness option for the LED display. Locate the 'DIMMER' or 'BRIGHTNESS' switch/button on the unit to adjust the display intensity to your comfort level, especially for nighttime viewing.

4.6 Swivel Base

The clock is equipped with a 90-degree swivel base, allowing you to adjust the viewing angle for optimal visibility from various positions in your room.

An infographic highlighting the clock's features: 1.8-inch red LED display, high/low alarm volume control, high/low display dimmer control, 90-degree swivel case, and optional 9V battery backup.

The Sharp LED Digital Alarm Clock shown rotating on its 90-degree swivel base, illustrating its adjustable viewزاويه.

A diagram indicating the dimensions of the Sharp LED Digital Alarm Clock: 6.25 inches wide, 4 inches high, and 2.15 inches deep.

5. سار سنڀال

• صفائي: گھڙي کي نرم، سڪل ڪپڙي سان صاف ڪريو. گھڙيال صاف ڪندڙ يا محلول استعمال نه ڪريو.
• بيٽري مٽائڻ: Replace the 9V backup battery annually or as needed to ensure continuous backup functionality.
• اسٽوريج: If storing the clock for an extended period, remove the backup battery to prevent leakage.

6. مسئلا حل ڪرڻ

• ڪابه ڊسپلي/ڪلاڪ ڪم نه ڪري رهي آهي:
  Ensure the power cord is securely plugged into a working 120V outlet. Check if the outlet is receiving power. If using battery backup, remember the display goes blank during power outages, but internal functions are maintained.
• الارم نه آواز:
  Verify that the alarm time is set correctly and the 'ALM' indicator is lit on the display. Check the alarm volume setting.
• Display Too Bright/Dim:
  Adjust the brightness using the 'DIMMER' or 'BRIGHTNESS' control.
• وقت جو صحيح نه هجڻ:
  Ensure the clock is connected to a stable power source. If frequent power interruptions occur, ensure the backup battery is fresh.

7. وضاحتون

8. وارنٽي ۽ سپورٽ

For warranty information or technical support, please refer to the documentation included with your purchase or visit the official Sharp webسائيٽ. ڪنهن به وارنٽي دعوائن لاءِ خريداري جي ثبوت طور پنهنجي خريداري جي رسيد رکو.