Peaktech P2170 LCR Meter Instruction Manual

1. تعارف

The Peaktech P2170 is a digital LCR meter with Equivalent Series Resistance (ESR) measurement capabilities. Designed for both component testing in professional environments and for service and maintenance tasks, its compact design and advanced features ensure precise measurements.

Key features include an illuminated multifunction display with a bargraph and a high measurement frequency of up to 100 kHz. The device also supports PC connectivity for data storage and analysis using the included software.

2. حفاظت جي ڄاڻ

ڊوائيس کي زخم يا نقصان کان بچڻ لاءِ هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:

• Read the entire manual before operating the device.
• Do not operate the meter if it appears damaged or if the insulation is compromised.
• Ensure correct battery installation and replacement.
• Avoid contact with live circuits when connecting or disconnecting test leads.
• Do not exceed the maximum input ratings specified for each function.
• ڊوائيس سڪي ۽ صاف رکو.

3. پراڊڪٽ ختمview

The Peaktech P2170 LCR Meter is a handheld device designed for measuring inductance (L), capacitance (C), and resistance (R), along with other parameters like ESR, DCR, Dissipation Factor (D), Quality Factor (Q), and Phase Angle (θ).

شڪل 1: سامهون view of the Peaktech P2170 LCR Meter, showing the display, function buttons, and input terminals.

3.1 اجزاء ۽ لوازمات

معياري پيڪيج ۾ ھيٺيون شيون شامل آھن:

• Peaktech P2170 LCR Meter
• USB انٽرفيس ڪيبل
• پي سي سافٽ ويئر
• Kelvin clips (test leads)
• حفاظتي سامان کڻڻ وارو ڪيس
• AAA batteries (6x 1.5V)
• ھدايت وارو دستور

Figure 2: Peaktech P2170 LCR Meter shown with its included accessories, including Kelvin clips, USB cable, and software CD.

4. سيٽ اپ

4.1 بيٽري لڳائڻ

The device operates on 6 x 1.5V AAA batteries. To install or replace batteries:

1. پڪ ڪريو ته ميٽر بند آهي.
2. ڊوائيس جي پوئين پاسي بيٽري جي ڪمپارٽمينٽ ڪَوَر کي ڳوليو.
3. Open the cover and insert 6 AAA batteries, observing the correct polarity markings.
4. بيٽري جي ڪمري واري ڍڪ کي محفوظ طور تي بند ڪريو.

An optional 12V 500mA power adapter can also be used for external power.

4.2 ٽيسٽ ليڊز کي ڳنڍڻ

Use the provided Kelvin clips for accurate measurements. Connect them to the input terminals as follows:

• Connect the red Kelvin clip to the ايڇ پوٽ ۽ ايڇ ڪر ٽرمينلز.
• Connect the black Kelvin clip to the ايل پوٽ ۽ لڪر ٽرمينلز.
• For 2-wire measurements, connect the test leads to ايڇ پوٽ ۽ ايل پوٽ.
• Ensure a secure connection to minimize measurement errors.

4.3 Software Installation (PC Link)

The included PC software allows for data logging and analysis. Follow these steps to install:

1. Insert the software CD into your computer's optical drive.
2. انسٽاليشن مڪمل ڪرڻ لاءِ اسڪرين تي ڏنل هدايتن تي عمل ڪريو.
3. Connect the meter to your PC using the supplied USB interface cable.
4. Launch the software and establish communication with the device. Refer to the software's help documentation for detailed usage.

5. آپريٽنگ هدايتون

5.1 پاور آن/آف

کي دٻايو پاور ميٽر کي آن يا آف ڪرڻ لاءِ بٽڻ.

5.2 ماپ جا طريقا

The P2170 supports various measurement modes. Press the فنڪ button to cycle through the primary measurement parameters:

• Ls (Series Inductance)
• Cs (Series Capacitance)
• Lp (Parallel Inductance)
• Cp (Parallel Capacitance)
• ڊي سي آر (DC Resistance)
• ESR (Equivalent Series Resistance)
• Rp (Parallel Resistance)
• D (Dissipation Factor)
• Q (Quality Factor)
• θ (Phase Angle)

The illuminated display will show the selected mode and measurement results.

5.3 Measurement Frequency Selection

کي دٻايو FREQ button to select the desired test frequency. Available frequencies include 100 Hz, 120 Hz, 1 kHz, 10 kHz, and 100 kHz. The chosen frequency will be displayed on the screen.

5.4 ڊيٽا هولڊ فنڪشن

کي دٻايو رکو button to freeze the current measurement reading on the display. Press it again to release the hold function.

5.5 حساب ڪتاب

To perform a calibration, ensure no component is connected to the input terminals. Press and hold the CAL button for approximately 2 seconds. Follow any on-screen prompts.

6. سار سنڀال

6.1 صفائي

ميٽر جي سي صاف ڪريوasing نرم سان، damp ڪپڙو. گھڙڻ وارا صاف ڪندڙ يا محلول استعمال نه ڪريو. صفائي ڪرڻ کان اڳ پڪ ڪريو ته ڊوائيس بند آهي ۽ ڪنهن به بجلي جي ذريعن کان ڌار ٿيل آهي.

6.2 بيٽري مٽائڻ

When the low battery indicator appears on the display, replace all 6 AAA batteries as described in Section 4.1.

6.3 اسٽوريج

If the meter is not used for an extended period, remove the batteries to prevent leakage. Store the device in its protective carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.

7. مسئلا حل ڪرڻ

If you encounter issues with your Peaktech P2170, refer to the following common problems and solutions:

• ميٽر آن نٿو ٿئي: Check battery installation and ensure batteries are not depleted. Try replacing with new batteries.
• غلط پڙهڻ:
  • پڪ ڪريو ته ٽيسٽ ليڊز صحيح طرح سان ڳنڍيل آهن ۽ خراب نه آهن.
  • Perform a calibration (Section 5.5).
  • Verify the correct measurement mode and frequency are selected for the component being tested.
  • Ensure the component is properly connected to the Kelvin clips.
• PC software not connecting:
  • USB ڪيبل ڪنيڪشن چيڪ ڪريو.
  • Ensure the software drivers are correctly installed.
  • Restart both the meter and the PC.

If the problem persists, contact Peaktech customer support.

8. وضاحتون

Detailed technical specifications for the Peaktech P2170 LCR Meter:

Figure 3: Detailed specifications table for the Peaktech P2170 LCR Meter, including measurement modes, ranges, frequencies, and physical characteristics.

9. وارنٽي ۽ سپورٽ

For warranty information, technical support, or service inquiries, please contact Peaktech directly or refer to their official webسائيٽ. خريداري جي ثبوت طور پنهنجي خريداري جي رسيد رکو.