Gravity G3-12D4 Subwoofer and WZ3000.1D Ampو lifيڪ تنصيب ۽ آپريشن دستياب

1. تعارف

This manual provides detailed instructions for the proper installation, operation, and maintenance of your Gravity G3-12D4 12-inch car audio subwoofer and Gravity WZ3000.1D Class D amplifier, along with the included 4-gauge amplifier installation kit. Please read this manual thoroughly before beginning installation to ensure correct setup and optimal performance.

2. حفاظت جي ڄاڻ

انسٽاليشن ۽ آپريشن دوران هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:

• Disconnect the vehicle's negative battery terminal before any wiring to prevent electrical shorts.
• پڪ ڪريو ته سڀئي وائرنگ صحيح طرح سان روٽ ٿيل ۽ محفوظ آهن ته جيئن تيز ڪنارن يا حرڪت ڪندڙ حصن کان نقصان نه ٿئي.
• Use appropriate gauge wiring as specified in this manual to handle current loads and prevent overheating.
• Install fuses at the battery and near the amplifier as instructed to protect against power surges.
• Avoid mounting components in locations that obstruct vehicle operation or safety features.
• Do not expose components to excessive moisture or extreme temperatures.
• جيڪڏهن توهان کي انسٽاليشن جي ڪنهن به مرحلي بابت پڪ ناهي ته پيشه ورانه مدد حاصل ڪريو.

3. پيڪيج مواد

پڪ ڪريو ته سڀئي شيون توهان جي پيڪيج ۾ موجود آهن:

• Gravity G3-12D4 12-inch Car Audio Subwoofer
• Gravity WZ3000.1D Class D Ampزندگي گذاريندڙ
• 4 گيج Amplifier Installation Kit, including:
• 17 ft. 4 Gauge Power Cable
• 3 ft. 4 Gauge Ground Cable
• Inline AGU Fuse Holder with 80A + 100A Fuses
• 17 ft. Double Shielded RCA Cable
• 17 ft. 18 Gauge Turn-On Cable
• 20 ft. 16 Gauge Speaker Wire
• All necessary accessories and terminals
• ريموٽ باس ڪنٽرول نوب

4. مصنوعات جون خاصيتون

Gravity G3-12D4 Subwoofer

• Dual 4 Ohm Voice Coil Configuration
• Competition Grade Pressed Paper Cone
• هاءِ رول فوم سرائونڊ
• Advanced Air Flow Cooling System

Gravity WZ3000.1D Ampزندگي گذاريندڙ

• Class D MOSFET Power Ampزندگي گذاريندڙ
• Stable at 1 Ohm, 2 Ohm, and 4 Ohm loads
• High and Low Level Inputs
• Variable Low Pass Crossover (LPF)
• متغير باس بوسٽ
• سبسونڪ فلٽر

4 گيج Ampلائفائر جي انسٽاليشن کٽ

• High Quality Thick 4 Gauge Power and Ground Cables
• Inline AGU Fuse Holder with multiple fuses for protection
• True Sound Double Shielded RCA Cable for clear signal transmission
• Complete set of accessories and terminals for a professional installation

5. سيٽ اپ ۽ تنصيب

Proper installation is crucial for performance and safety. If you are not confident in your ability to install this system, please consult a professional installer.

5.1. سب ووفر کي لڳائڻ

The G3-12D4 subwoofer requires a suitable enclosure (not included) for optimal performance. Ensure the enclosure is properly sealed and sized according to subwoofer specifications. Mount the subwoofer securely to the enclosure using appropriate screws, ensuring a tight seal around the mounting flange.

تصوير: سامهون view of the Gravity G3-12D4 12-inch subwoofer, showing the black cone with a red Gravity logo and red stitching on the foam surround.

تصوير: پوئين پاسي view of the Gravity G3-12D4 12-inch subwoofer, displaying the magnet structure and speaker terminals.

5.2. لڳائڻ Ampزندگي گذاريندڙ

Select a mounting location for the WZ3000.1D amplifier that is dry, well-ventilated, and protected from physical damage. Common locations include under a seat, in the trunk, or mounted to a custom amplifier rack. Ensure there is sufficient airflow around the amplifier for cooling. Secure the amplifier firmly using screws.

تصوير: پاسي view of the Gravity WZ3000.1D amplifier, showing the heat sink fins for cooling.

5.3. سسٽم کي وائرنگ ڪرڻ

Follow these steps carefully for wiring the amplifier and subwoofer:

1. Power Cable (Red 4 Gauge): Run the 17 ft. 4 gauge power cable from the vehicle's positive battery terminal to the amplifier location. Install the inline AGU fuse holder within 18 inches (45 cm) of the battery. Do not insert the fuse until all wiring is complete.
2. Ground Cable (Black 4 Gauge): Connect the 3 ft. 4 gauge ground cable from the amplifier's ground terminal to a clean, unpainted metal surface on the vehicle chassis. Ensure a solid, low-resistance connection. The ground point should be as short as possible.
3. Remote Turn-On Cable (Blue 18 Gauge): Connect the 17 ft. 18 gauge turn-on cable from the amplifier's REM terminal to the remote turn-on output of your head unit. This cable signals the ampهيڊ يونٽ سان آن ۽ آف ڪرڻ لاءِ لائفائر.
4. آر سي اي سگنل ڪيبل: Connect the 17 ft. double shielded RCA cable from the RCA outputs of your head unit to the RCA INPUTs on the WZ3000.1D ampوierيڪ زنده
5. Speaker Wiring (16 Gauge): Connect the 20 ft. 16 gauge speaker wire from the amplifier's speaker output terminals to the G3-12D4 subwoofer. Ensure correct polarity (+ to + and - to -). For a single G3-12D4 (dual 4-ohm voice coils), you can wire the voice coils in parallel for a 2-ohm load or in series for an 8-ohm load. The WZ3000.1D amplifier is stable down to 1 ohm, so a 2-ohm parallel configuration is recommended for maximum power output.
6. ريموٽ باس ڪنٽرول: Connect the remote bass control knob to the dedicated REMOTE port on the amplifier. Mount the knob in an accessible location for easy adjustment.

Image: Front panel of the Gravity WZ3000.1D amplifier, displaying RCA inputs, remote control port, and various adjustment knobs.

Image: Rear panel of the Gravity WZ3000.1D amplifier, showing the power input terminals (+12V, GND, REM) and speaker output terminals.

Image: The remote bass control knob, used for adjusting subwoofer output level from the driver's seat.

5.4. Final Connection

Once all wiring is securely connected and checked for shorts, insert the appropriate fuse (80A or 100A, depending on your system's power draw) into the inline AGU fuse holder near the battery. Reconnect the vehicle's negative battery terminal.

6. آپريٽنگ هدايتون

After installation, power on your head unit. The amplifier should turn on automatically (indicated by a power LED). Adjust the amplifier settings as follows:

• GAIN (Input Level): Start with the GAIN control at minimum. Play a familiar track with strong bass at about 75% of your head unit's maximum volume. Slowly increase the GAIN until you hear distortion, then back off slightly. This sets the amplifier's input sensitivity to match your head unit's output.
• LPF (گهٽ پاسو فلٽر): This control filters out high frequencies, allowing only low frequencies to pass to the subwoofer. Set the LPF between 40 Hz and 180 Hz. A common starting point is 80 Hz, but adjust to blend smoothly with your main speakers.
• SUBSONIC Filter: This filter removes extremely low frequencies below the audible range that can cause damage to the subwoofer. Set it between 0 Hz and 50 Hz. A setting around 25-30 Hz is often suitable for ported enclosures, while sealed enclosures may not require it as much.
• BASS BOOST FREQ: This selects the frequency at which the bass boost will be applied. Adjust this to enhance a specific bass frequency range.
• پرش ترقيء: This control increases the output level at the selected bass boost frequency (0-12 dB). Use sparingly to avoid distortion and potential speaker damage.
• ريموٽ باس ڪنٽرول: This knob allows you to adjust the subwoofer's output level conveniently from your listening position without affecting other ampلائفائر سيٽنگون.

7. سار سنڀال

To ensure longevity and optimal performance of your car audio system:

• سڀني وائرنگ ڪنيڪشنن کي باقاعدي طور تي تنگي ۽ سنکنرن لاءِ چيڪ ڪريو.
• رکي amplifier and subwoofer free from dust and debris. Use a soft, dry cloth for cleaning.
• کي يقيني بڻايو amplifier's cooling fins are not obstructed to prevent overheating.
• Avoid exposing the subwoofer cone to direct sunlight for extended periods, as UV rays can degrade materials.

8. مسئلا حل ڪرڻ

جيڪڏهن توهان کي مسئلا درپيش اچن ٿا، ته هيٺ ڏنل عام مسئلن ۽ حلن جو حوالو ڏيو:

9. وضاحتون

Gravity G3-12D4 Subwoofer

• Speaker Size: 12 Inches
• Voice Coil Configuration: Dual 4 Ohm
• Peak Power: 2000 Watts (each)
• RMS Power: 1000 Watts (each)
• Frequency Response: 30 - 500 Hz
• حساسيت: 87 ڊي بي

Gravity WZ3000.1D Ampزندگي گذاريندڙ

• Max Power: 3000W @ 1 Ohm
• ڪلاس: ڊي
• Stable Impedance: 1 Ohm, 2 Ohm, 4 Ohm
• Signal-to-Noise Ratio (S/N): 70 dB
• تعدد جواب: 8 Hz ~ 180 Hz
• ٽوٽل هارمونڪ ڊسٽرشن (THD): 0.2%
• Bass Boost Level: 0 ~ 12 dB
• Low Pass Filter (LPF): 40 Hz ~ 180 Hz
• Subsonic Filter: 0 ~ 50 Hz
• Dimensions (L×W×H): 223.5mm (8.8 in) × 211mm (8.3 in) × 64.5 mm (2.5 in)

4 گيج Ampلائفائر جي انسٽاليشن کٽ

• Power Cable: 17 ft. 4 Gauge
• Ground Cable: 3 ft. 4 Gauge
• Fuse Holder: Inline AGU with 80A + 100A Fuses
• RCA Cable: 17 ft. Double Shielded
• Turn-On Cable: 17 ft. 18 Gauge
• Speaker Wire: 20 ft. 16 Gauge

10. وارنٽي ۽ سپورٽ

Gravity products are designed for reliability and performance. For specific warranty terms and conditions, please refer to the warranty card included with your product or contact Gravity customer support. Keep your purchase receipt as proof of purchase for any warranty claims.

For technical support or inquiries, please visit the official Gravity webسائيٽ يا انهن جي ڪسٽمر سروس کاتي سان رابطو ڪريو.