1. تعارف
This manual provides essential information for the safe and effective installation, operation, and maintenance of the Eaton CHPSURGE Plug-On Neutral Surge Protective Device (SPD). This Type 2 SPD is designed to protect your home's electrical system and connected equipment from damaging power surges. Please read this manual thoroughly before installation or use.
2. حفاظت جي ڄاڻ
خبردار: Risk of electric shock. Installation and servicing of this device must be performed by qualified electrical personnel only. Failure to follow these instructions may result in serious injury or death.
- Always disconnect power at the main service panel before installing or servicing the surge protective device.
- تصديق ڪريو ته بجلي بند آهي هڪ وول استعمال ڪنديtagاي جاچ ڪندڙ اڳتي وڌڻ کان اڳ.
- پڪ ڪريو ته انسٽاليشن دوران سڀئي مقامي ۽ قومي اليڪٽريڪل ڪوڊس تي عمل ڪيو وڃي.
- Do not install this device in a wet or damp جڳھ
3. پراڊڪٽ ختمview
The Eaton CHPSURGE is a 2-pole, plug-on neutral surge protective device designed for use in Eaton CH series load centers. It provides whole-home surge protection by diverting harmful transient voltages away from sensitive electronics. The device features a green LED indicator to confirm operational status.
تصوير 1: سامهون view of the Eaton CHPSURGE device. This image shows the compact, black housing of the surge protective device, with the Eaton logo and 'SURGE PROTECTOR' label visible. A green indicator light is present, labeled 'PROTECTED WHEN LIT', signifying operational status. The model number 'CHPSURGE' is also clearly displayed.
Image 2: Eaton CHPSURGE device alongside its retail packaging. The packaging displays the Eaton logo, 'CHPSURGE', 'QTY. 1', and 'SURGE-PROTECTIVE DEVICE TYPE 2', along with voltage ratings '120 / 240 V~' and '2 POLE'. A barcode with the number 786689353674 is also visible.
4. سيٽ اپ (انسٽاليشن)
The Eaton CHPSURGE is a permanently connected device designed for installation within a compatible Eaton CH series load center. It is installed on the load side of the service entrance overcurrent protective device.
- پاور ڪنيڪشن: Locate your main electrical panel and turn off the main breaker to completely de-energize the panel. Verify power is off using a voltagاي جاچ ڪندڙ.
- پينل رسائي: Carefully remove the cover of your electrical panel.
- ڊوائيس لڳائڻ: Identify two adjacent available spaces in your Eaton CH series load center. The CHPSURGE device is a 2-pole breaker form factor.
- تنصيب: Insert the CHPSURGE device into the two available breaker slots. Ensure it is firmly seated on the bus bar. The plug-on neutral feature simplifies connection to the neutral bus.
- وائرنگ: Connect the neutral wire from the surge protective device to the neutral bus bar in the panel. Connect the ground wire to the ground bus bar. Ensure all connections are tight and secure.
- Panel Closure: Replace the electrical panel cover, ensuring all wires are clear of the cover and screws.
- پاور بحالي: Turn the main breaker back on. The green LED indicator on the CHPSURGE device should illuminate, indicating it is operational and providing protection.
5. آپريٽنگ
Once properly installed and power is restored, the Eaton CHPSURGE device operates continuously to protect your electrical system. The green LED indicator on the front of the device signifies that the surge protection is active and functioning correctly. The device automatically detects and diverts harmful voltage surges, protecting your home's electrical circuits and connected appliances.
6. سار سنڀال
The Eaton CHPSURGE device requires minimal maintenance. Periodically check the green LED indicator on the front of the device. As long as the LED is illuminated, the device is providing surge protection.
- LED اشارو چيڪ: Visually inspect the device's LED indicator at least once a month.
- Device Replacement: If the green LED indicator is off, it signifies that the device has absorbed a significant surge event and is no longer providing protection. The device must be replaced immediately to restore surge protection.
7. مسئلا حل ڪرڻ
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| Green LED indicator is off. | The device has absorbed a surge and is no longer functional. | Replace the Eaton CHPSURGE device with a new one. |
| No power to the panel after installation. | Main breaker is off or tripped. | Ensure the main breaker in your electrical panel is in the 'ON' position. If it tripped, reset it. |
| Device does not fit in panel. | Incorrect panel type. | This device is designed for Eaton CH series panels only. Verify your panel type. Do not attempt to force installation into incompatible panels. |
8. وضاحتون
- پيداوار جو قسم: Type CH Circuit Breaker Surge Protective Device
- پولس: ٻه قطب
- ڪنيڪشن جو قسم: پلگ ان غير جانبدار
- Surge Protection Type: ٽائپ 2 SPD
- شارٽ سرڪٽ ريٽنگ: 10 ڪي
- مداخلت جي درجه بندي: 10 ڪي اي سي
- تعدد جي درجه بندي: 50/60 Hz
- موجوده وهڪري: 18 ڪي
- وڌ ۾ وڌ مسلسل آپريٽنگ Voltage (MCOV): 150 V LN، 300 V LL
- جلدtage: 240 وولٽ
- سرٽيفڪيشن: UL 1449 3rd Edition Listed
- پيداوار جي ماپ: تقريبن 7 x 4 x 0.01 انچ
- شيء جو وزن: تقريبن 7 آونس
9. وارنٽي ۽ سپورٽ
Eaton products are manufactured to high-quality standards and are backed by a manufacturer's warranty. For specific warranty details, terms, and conditions, please refer to the documentation included with your purchase or visit the official Eaton webسائيٽ.
For technical assistance, troubleshooting beyond the scope of this manual, or to inquire about replacement parts, please contact Eaton customer support. Have your product model number (CHPSURGE) and purchase information ready when contacting support.
ايٽن آفيشل Webسائيٽ: www.eaton.com
