تعارف
This user manual provides detailed instructions for the installation, operation, and maintenance of your Lanzar Car Amplifier Bundle, which includes the VCT4110 4-Channel High Power MOSFET Amplifier and the HTG137 2000 Watt Monoblock Car Amplifier. Please read this manual thoroughly before attempting installation or operation to ensure proper use and to prevent damage to the units or your vehicle's electrical system.
حفاظت جي ڄاڻ
انسٽاليشن ۽ آپريشن دوران هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:
- Disconnect the vehicle's negative battery terminal before beginning any installation.
- Ensure proper grounding for all components to prevent electrical shorts and damage.
- بيان ڪيل طور تي پاور، گرائونڊ، ۽ اسپيڪر ڪنيڪشن لاءِ مناسب گيج وائرنگ استعمال ڪريو.
- انسٽال ڪرڻ کان پاسو ڪريو amplifiers in locations exposed to direct sunlight, excessive heat, moisture, or dust.
- محفوظ طور تي نصب ڪريو amplifiers to prevent movement during vehicle operation.
- جيڪڏهن توهان انسٽاليشن جي عمل جي ڪنهن به حصي بابت پڪ نه آهيو، ته پوءِ هڪ پيشيور ڪار آڊيو انسٽالر سان صلاح ڪريو.
پيداوار ختمview
Lanzar VCT4110 4-Channel Ampزندگي گذاريندڙ
The Lanzar VCT4110 is a 2000 Watt 4-Channel High Power MOSFET Amplifier designed for versatile car audio setups. It features variable high-pass and low-pass crossovers, variable input level control, and a bass boost switch. Its slim design allows for easier installation in various vehicle spaces. This amplifier is 2 Ohm stable and includes thermal, overload, and short circuit protection for reliable performance.
Lanzar HTG137 Monoblock Ampزندگي گذاريندڙ
The Lanzar HTG137 is a 2000 Watt Monoblock Amplifier from the Heritage Series, optimized for driving subwoofers with powerful bass. It includes an electronic crossover network, bass boost circuitry, and low/high pass filters. This amplifier is 2 Ohm stable and features RCA inputs and line outputs for system expansion. It also incorporates power and protection LED indicators and soft turn-on/off circuitry.
سيٽ اپ ۽ تنصيب
توهان جي ڊوائيس جي بهترين ڪارڪردگي ۽ ڊگهي عمر لاءِ صحيح تنصيب انتهائي اهم آهي amplifiers. Follow these steps carefully.
عام انسٽاليشن ھدايتون
- پاور وائرنگ: Connect the main power wire (typically 4-gauge or 8-gauge depending on total wattage) directly from the positive terminal of the vehicle's battery to the ampلائفائر جو +12V ٽرمينل. بيٽري جي 18 انچ اندر هڪ ان-لائن فيوز هولڊر نصب ڪريو.
- گرائونڊ وائرنگ: Connect the ground wire (same gauge as power wire) from the ampگاڏي جي چيسس تي هڪ صاف، غير رنگ ٿيل ڌاتو جي مٿاڇري تي لائفائر جي GND ٽرمينل کي. هڪ مضبوط، گهٽ مزاحمتي ڪنيڪشن کي يقيني بڻايو.
- ريموٽ ٽرن آن: پنهنجي هيڊ يونٽ جي ريموٽ آئوٽ پُٽ مان ريموٽ ٽرن آن وائر کي سان ڳنڍيو ampلائفائر جو REM ٽرمينل. هي تار سگنل ڏئي ٿو ampتوهان جي هيڊ يونٽ سان آن ۽ آف ڪرڻ لاءِ لائفائر.
- آر سي اي انپٽس: پنهنجي هيڊ يونٽ جي پري کان آر سي اي ڪيبلز ڳنڍيو.amp کي آئوٽ پُٽ ampلائفائر جا آر سي اي ان پٽ جيڪس.
- اسپيڪر وائرنگ: اسپيڪر تارن کي ڪنيڪٽ ڪريو amplifier's speaker output terminals to your speakers. Pay close attention to polarity (+ to + and - to -).
Lanzar VCT4110 4-Channel Ampوierيڪ مضبوط رابطا
The VCT4110 features clearly labeled input and output panels. The right panel includes power (BATT, REM, GND) and speaker output terminals (CH1-CH4, BRIDGEABLE). The left panel provides RCA inputs (CH1/2, CH3/4), gain controls (LEVEL), and crossover frequency adjustments (X-OVER). Ensure all connections are secure and properly insulated.
- پاور ان پٽ: Connect +12V, REM, and GND as per general guidelines.
- اسپيڪر جا نتيجا: Connect up to four speakers. For bridged operation (2-channel mode), connect speakers to the designated bridged terminals (e.g., CH1+ and CH2- for one bridged channel). Refer to the amplifier's diagram for specific bridging instructions.
- RCA ان پٽ: پنهنجي هيڊ يونٽ جي آر سي اي آئوٽ پُٽ کي سان ڳنڍيو amplifier's CH1/2 and CH3/4 inputs.
- لائين آئوٽ: The VCT4110 includes a line output for connecting additional ampگھڻن ۾ لائفائرamp سسٽم.
Lanzar HTG137 Monoblock Ampوierيڪ مضبوط رابطا
The HTG137's connection panel includes power input (GND, REM, BATT), speaker output, RCA inputs (LCH, RCH), and line outputs. Controls for gain, bass boost, LPF (Low Pass Filter), and Subsonic filter are also present. Ensure all connections are tight and free from short circuits.
- پاور ان پٽ: Connect +12V, REM, and GND as per general guidelines.
- اسپيڪر آئوٽ: Connect your subwoofer(s) to the single speaker output terminal. Ensure the subwoofer's impedance matches the amplifier's stable impedance (2 Ohm stable).
- RCA ان پٽ: Connect your head unit's subwoofer or full-range RCA outputs to the amplifier's LCH and RCH inputs.
- لائين آئوٽ: The HTG137 provides line-out jacks for daisy-chaining to another amplifier without needing external splitters.
آپريشن ڪندي Ampجان بچائيندڙ
هڪ دفعو انسٽال ٿيڻ کان پوءِ، ترتيب ڏيو ampبهترين آواز جي ڪارڪردگي لاءِ لائفائر سيٽنگون.
Gain Control (LEVEL)
حاصل ڪنٽرول سان ملندو آهي ampآئوٽ پُٽ واليم ڏانهن لائفائر جي ان پٽ حساسيتtagتوهان جي هيڊ يونٽ جو e. گهٽ ۾ گهٽ گين سيٽ سان شروع ڪريو. پنهنجي هيڊ يونٽ جي وڌ ۾ وڌ حجم جي لڳ ڀڳ 75٪ تي هڪ واقف ٽريڪ کيڏيو. آهستي آهستي وڌايو amplifier's gain until you hear distortion, then back it off slightly. This is not a volume control.
ڪراس اوور سيٽنگون
- VCT4110 (4-Channel):
- Variable Hi-Pass (HPF): 40 Hz - 250 Hz. Use for full-range speakers to filter out low frequencies they cannot reproduce, preventing distortion.
- Variable Low-Pass (LPF): 40 Hz - 250 Hz. Use for subwoofers (if bridging channels for subwoofers) to filter out high frequencies.
- HTG137 (Monoblock):
- ايل پي ايف فريڪ. جواب: 50Hz - 250Hz. Essential for subwoofers to ensure only low frequencies are reproduced.
- سبسونڪ فلٽر: Filters out extremely low frequencies below the audible range, which can waste amplifier power and damage subwoofers. Typically set around 20-30Hz.
پرش ترقيء
ٻئي amplifiers feature a bass boost function (VCT4110: 0-18dB switch; HTG137: variable). Use this feature sparingly as excessive bass boost can lead to distortion and potential speaker damage. Adjust to personal preference while monitoring for clarity.
LED اشارا
- پاور LED: روشني ٿئي ٿي جڏهن amplifier is receiving power and operating normally.
- حفاظت LED: Illuminates (often red) when the amplifier enters protection mode due to thermal overload, short circuit, or low voltage. If this LED lights up, turn off your system immediately and troubleshoot the issue.
سار سنڀال
باقاعده سار سنڀال توهان جي ڊگهي عمر ۽ بهترين ڪارڪردگي کي يقيني بڻائي ٿي ampجان بچائيندڙ.
- صفائي: وقتي طور تي صاف ڪريو amplifier's exterior with a soft, dry cloth. Do not use liquid cleaners or solvents. Ensure cooling fins are free of dust and debris to maintain proper heat dissipation.
- ڪنيڪشن: Occasionally check all power, ground, remote, RCA, and speaker connections to ensure they are secure and free from corrosion. Loose connections can cause performance issues or damage.
- وينٽيليشن: چوڌاري علائقي کي يقيني بڻايو وڃي amplifiers remains clear to allow for adequate airflow and cooling. Do not obstruct the cooling fins.
مشڪلاتون
If you experience issues with your Lanzar amplifiers, refer to the following common problems and solutions:
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| بجلي ناهي (پاور ايل اي ڊي بند) | ڦاٽل فيوز، ڍلو پاور/گرائونڊ/ريموٽ تار، هيڊ يونٽ مان ڪو به ريموٽ سگنل نه. | ان لائن فيوز چيڪ ڪريو ۽ amplifier fuses. Verify all power, ground, and remote connections are secure and receiving voltage. Check head unit's remote output. |
| تحفظ LED آن | Overheating, short circuit in speaker wiring, speaker impedance too low, low voltage. | اجازت ڏيو amplifier to cool. Check speaker wiring for shorts (bare wires touching). Verify speaker impedance is within amplifier's stable range. Check vehicle's battery voltage. |
| ڪوبه آواز آئوٽ | Loose RCA cables, incorrect gain setting, muted head unit, faulty speakers. | Ensure RCA cables are securely connected at both ends. Adjust gain. Check head unit volume and mute settings. Test speakers with another audio source if possible. |
| بگڙيل آواز | Gain set too high, incorrect crossover settings, poor ground connection, damaged speakers. | Reduce gain. Adjust crossover frequencies. Verify ground connection is solid. Inspect speakers for damage. |
| انجن جو شور/ گوڙ | Poor grounding, RCA cables too close to power wires, faulty alternator. | Improve ground connection. Reroute RCA cables away from power wires. Consider a ground loop isolator. Have alternator checked. |
وضاحتون
Lanzar VCT4110 4-Channel Ampزندگي گذاريندڙ
| خاصيت | تفصيل |
|---|---|
| پاور آئوٽ (4 Ohms) | 500W X 4 |
| Bridged Output (2 Ohms) | 1000W X 2 |
| Ampوierيڪ ڪلاس | MOSFET |
| 2 Ohm مستحڪم | ها |
| متغير هاء-پاس | 40 هرٽز - 250 هرٽز |
| متغير گھٽ-پاس | 40 هرٽز - 250 هرٽز |
| Variable Input Level (Gain) | 6V - 200mV |
| باس بوسٽ سوئچ | 0-18 ڊي بي |
| تحفظ | Thermal / Overload / Short Circuit |
| تعدد جواب | 15 Hz - 30K Hz |
| سگنل کان شور جي نسبت | >95dB |
| ٽي ايڇ ڊي | 0.1% |
| فيوز جو قسم | 2x30 Amp Maxi Type |
| ڊائرنس (ڊبليو ايڇ ڊي ايل) | 10.63'' x 1.78'' x 14.02'' |
Lanzar HTG137 Monoblock Ampزندگي گذاريندڙ
| خاصيت | تفصيل |
|---|---|
| RMS پاور (4 Ohm) | 1 x 650 واٽ |
| چوٽي جي طاقت (4 اوهم) | 1 x 1250 واٽ |
| RMS پاور (2 Ohm) | 1 x 1500 واٽ |
| Max Power (2 Ohm) | 1 x 2000 واٽ |
| Ampوierيڪ ڪلاس | MOSFET (1 Channel) |
| 2 Ohm مستحڪم | ها |
| ٽي ايڇ ڊي | <0.01٪ |
| S/N تناسب | >90dB |
| تعدد جواب | 10 هز - 45 ڪلو هرٽز |
| HPF Freq. Resp. | 80Hz |
| LPF Freq. Resp. | 50Hz - 250Hz |
| فيوز | 40A x 1 |
| طول و عرض (L x H x W) | 13.0'' x 2.4'' x 8.8'' |
وارنٽي ۽ سپورٽ
Lanzar products are designed for reliability and performance. For specific warranty details, please refer to the documentation included with your purchase or visit the official Lanzar website. For technical support or service inquiries, please contact Lanzar customer service.
هڪ سرڪاري PDF استعمال ڪندڙ دستياب پڻ ڊائون لوڊ لاءِ موجود آهي: پي ڊي ايف يوزر مينوئل ڊائون لوڊ ڪريو
