اوسمو يو وي-پروٽيڪشن آئل ايڪسٽرا 420 ڪليئر: ايڪسٽيريئر ووڊ فنش انسٽرڪشن مينوئل

1. تعارف

The Osmo UV-Protection Oil Extra 420 Clear is a clear, satin wood finish designed for exterior wood surfaces. This natural oil-based product offers advanced UV protection, helping to preserve the natural beauty of wood while preventing graying. Its microporous surface allows the wood to breathe, reducing swelling and shrinkage, and it is water repellent. This finish will not crack, peel, or flake, and when used as a topcoat on already color-treated wood, it significantly extends renovation intervals.

2. حفاظت جي ڄاڻ

Always read the product label and safety data sheet before use. Ensure adequate ventilation during application and drying. Keep out of reach of children. Avoid contact with skin and eyes. In case of contact, rinse immediately with plenty of water. Do not ingest. Dispose of product and packaging responsibly according to local regulations.

3. پراڊڪٽ ختمview

A small metal can of Osmo UV-Protection Oil Extra, labeled '420 Clear' and '0.125 Liter'. The label is white with green and red accents, featuring the Osmo logo and product name.

اهم خاصيتون:

• Clear, satin finish for exterior wood.
• Based on natural oils.
• High UV protection to prevent graying.
• Microporous, allowing wood to breathe.
• پاڻي کان بچاءُ وارو.
• Resistant to cracking, peeling, and flaking.
• Extends renovation intervals when used as a topcoat.

4. تياري

1. مٿاڇري جي حالت: The wood surface must be clean, dry, and frost-free. Ensure the wood moisture content does not exceed 20%.
2. صفائي: Remove any dirt, dust, loose particles, or old flaking finishes. For previously oiled or stained wood, clean thoroughly. For new or untreated wood, a light sanding may be beneficial, followed by dust removal.
3. Existing Finishes: Old paints and lacquers must be completely removed. Old open-pored stains or oils should be cleaned and lightly sanded.
4. Wood Species: For exotic hardwoods, allow them to weather for at least 4 weeks before treatment to ensure proper absorption.
5. ڇڪڻ: Stir the Osmo UV-Protection Oil Extra thoroughly before use.

5. ايپليڪيشن

General Application Guidelines:

• Apply thinly and evenly along the wood grain.
• Use a good quality brush or roller.
• Ensure good ventilation during application and drying.
• Protect surrounding areas from splashes.

قدم بہ قدم درخواست:

1. پهريون ڪوٽ: Apply a thin, even coat of Osmo UV-Protection Oil Extra to the prepared, dry wood surface. Work along the wood grain.
2. سڪل وقت: Allow the first coat to dry for approximately 10-12 hours under good ventilation. Lower temperatures and higher humidity will extend drying time.
3. ٻيو ڪوٽ: After the first coat is completely dry, apply a second thin, even coat.
4. آخري سڪل: Allow the second coat to dry for another 10-12 hours. The surface should be fully cured and ready for use after 24-48 hours.

اهم نوٽ: For optimal results and longevity, always follow the manufacturer's instructions provided on the product packaging.

6. سار سنڀال

• باقاعده صفائي: Clean the treated surface regularly with a damp cloth and a mild, pH-neutral cleaner. Avoid harsh chemicals or abrasive cleaners.
• ٻيهر درخواست: The frequency of re-application depends on the level of weathering and exposure. Typically, a maintenance coat is recommended every 3-5 years, or when the surface begins to show signs of wear or reduced water repellency.
• Spot Repair: Small areas of wear can be spot-repaired by cleaning the area and applying a thin coat of Osmo UV-Protection Oil Extra.

7. مسئلا حل ڪرڻ

8. وضاحتون

9. وارنٽي ۽ سپورٽ

For specific warranty information regarding Osmo UV-Protection Oil Extra, please refer to the product packaging or contact Osmo directly. General product support and technical advice can be obtained through the official Osmo website or by contacting their customer service department. Always retain your proof of purchase.

وڌيڪ مدد لاءِ، مھرباني ڪري دورو ڪريو Osmo Store on Amazon.