ريڊيو ماسٽر R84 V2 4ch SFHSS مطابقت رکندڙ PWM وصول ڪندڙ هدايت نامو

1. تعارف

The Radiomaster R84 V2 is a compact 4-channel PWM receiver designed for various remote-controlled models. It offers compatibility with Frsky D8, D16, and Futaba SFHSS signal formats, making it suitable for use with MPM (Multi-Protocol Module) radios. This manual provides essential information for setting up, operating, and maintaining your R84 V2 receiver.

2. وضاحتون

پيداوار جي ماپ: 3 x 2 x 1 انچ

شيء جو وزن: 0.64 اونس

3. پيڪيج مواد

• 1 x Radiomaster R84 V2 Receiver

4. Setup - Binding Process

The Radiomaster R84 V2 receiver is compatible with Frsky D8, D16, and Futaba SFHSS protocols. It is designed for use with Multi-Protocol Module (MPM) radios. The specific binding procedure may vary slightly depending on your transmitter's firmware and module settings. Always refer to your transmitter's instruction manual for detailed binding steps for D8, D16, or SFHSS protocols.

General Binding Steps:

1. وصول ڪندڙ تيار ڪريو: Ensure the R84 V2 receiver is connected to a power source (4.5-8.4V).
2. Enter Bind Mode: Typically, you will need to power cycle the receiver multiple times (e.g., plug and unplug three times) to put it into bind mode. The receiver's LED will usually indicate bind mode (e.g., a rapid double blink).
3. Transmitter Bind: On your MPM-equipped transmitter, select the appropriate protocol (Frsky D8, D16, or Futaba SFHSS) and initiate the binding process.
4. Confirm Bind: Once binding is successful, the receiver's LED will typically turn solid, indicating a stable connection.

نوٽ: This receiver does not support direct binding with Frsky transmitters; it requires an MPM radio.

5. آپريٽنگ

After successful binding, the R84 V2 receiver will output PWM signals on its 4 channels. Connect your servos, ESCs, or other PWM-controlled devices to the corresponding channels (CH1-CH4) on the receiver.

• چينل: 4 independent PWM output channels.
• طاقت: Ensure your power source (e.g., flight controller, BEC) provides power within the 4.5-8.4V range.
• Antenna لڳائڻ: For optimal signal reception and range, ensure the receiver antennas are positioned away from carbon fiber, metal, and other signal-blocking materials. Orient the two antennas at a 90-degree angle to each other if possible.

6. سار سنڀال

To ensure the longevity and reliable performance of your R84 V2 receiver, follow these maintenance guidelines:

• صاف رکو: Regularly inspect the receiver for dirt, dust, or moisture. Clean gently with a soft, dry brush or cloth.
• جسماني نقصان کان بچاء: Protect the receiver from impacts and excessive vibrations. Secure it properly within your model.
• Antenna Integrity: Ensure antennas are not cut, kinked, or damaged. Damaged antennas can significantly reduce range and signal quality.
• گرمي پد: Avoid operating or storing the receiver in extreme temperatures.

7. مسئلا حل ڪرڻ

If you encounter issues with your R84 V2 receiver, consider the following:

• No Connection/No Control: Re-attempt the binding process, ensuring your transmitter is set to the correct protocol (D8, D16, or SFHSS) for your MPM radio.
• وقفي وقفي سان سگنل: Check antenna placement and ensure they are not obstructed or damaged. Verify the power supply to the receiver is stable and within the specified voltage حد.
• غلط سروو حرڪت: Verify your channel mapping and servo directions in your transmitter settings.
• پاور مسئلا: Ensure the power input is between 4.5-8.4V. Incorrect voltage can damage the receiver or prevent proper operation.

For further troubleshooting, consult your MPM radio's instruction manual or the Radiomaster official support resources.

8. حفاظت جي ڄاڻ

Always refer to the instruction manual before use and operate your RC equipment responsibly. Ensure all connections are secure and correct before powering on your model.

9. وارنٽي ۽ سپورٽ

For warranty information, technical support, or further assistance, please visit the official RADIOMASTER webسائيٽ تي وڃو يا انهن جي ڪسٽمر سروس سان رابطو ڪريو. ڪنهن به وارنٽي دعوائن لاءِ خريداري جو ثبوت رکو.