Phillips Aruma Digital Smart Lock Instruction Manual

1. تعارف

The Phillips Aruma Digital Smart Lock offers a secure and convenient access solution for homes and offices. This lock features multiple entry methods including fingerprint, password, proximity card, and mechanical key. Designed for both metal and wooden doors, it accommodates door thicknesses from 35 mm to 80 mm and adjustable backsets of 60 mm or 70 mm. It is suitable for both left and right-hand hinged doors. The lock operates on 4 AA alkaline batteries and includes an emergency 5V port and mechanical key override for power failures. It is rated IP54 for mild weather resistance.

2. پيڪيج مواد

انسٽاليشن کان اڳ، مھرباني ڪري تصديق ڪريو ته سڀئي جزا پيڪيج ۾ موجود آھن:

• Phillips Aruma Digital Smart Lock unit
• Mounting hardware (screws, spindle)
• انسٽاليشن دستي
• 4 proximity cards (Mifare 13.56Mhz sensor)
• 2 mechanical keys (Forja PH6/SC1)
• 4 AA alkaline batteries (1.5 V)

شڪل 1: سامهون view of the Phillips Aruma Digital Smart Lock, showing the keypad and fingerprint sensor.

شڪل 2: پاسي view of the Phillips Aruma Digital Smart Lock, illustrating its profile.

شڪل 3: پوئتي view of the Phillips Aruma Digital Smart Lock, showing the internal components and battery compartment.

انباڪسنگ وڊيو

3. ٽيڪنيڪل وضاحتون

4. انسٽاليشن گائيڊ

Please read these instructions carefully before beginning installation. It is recommended to install the lock with the door open. Do not close your door until the batteries are inserted and the lock is fully tested.

انسٽاليشن وڊيو

اهم تنصيب جا مرحلا:

1. دروازو تيار ڪريو: Ensure your door meets the specified thickness (35-80mm) and bore hole backset (60mm or 70mm).
2. ليچ بولٽ انسٽال ڪريو: Insert the latch bolt into the door edge and secure it with screws. Ensure the spindle hole is correctly oriented (squarely straight to the ground).
3. Adjust Handle Direction (Front Panel): If necessary, adjust the direction of the handle on the front panel by rotating it to the left or right.
4. فرنٽ پينل انسٽال ڪريو: Slide the lock spindle and wire connector through the door holes. Secure the front panel to the door.
5. انسٽال ڪرڻ واري پليٽ: Slide the mounting plate over the spindle and wire connector, threading the wire connector through the designated hole. Secure the mounting plate with screws appropriate for your door thickness.
6. وائر ڳنڍڻ: Connect the wire connector from the front panel to the corresponding port on the back panel.
7. Adjust Handle Direction (Back Panel): If necessary, adjust the direction of the handle on the back panel by rotating it to the left or right.
8. پوئتي پينل انسٽال ڪريو: Carefully align the back panel with the mounting plate and secure it with screws.
9. بيٽرين کي انسٽال ڪريو. Open the battery compartment on the back panel and insert 4 AA alkaline batteries, ensuring correct polarity. Close the battery box.

5. آپريٽنگ هدايتون

The Phillips Aruma Digital Smart Lock offers multiple ways to unlock your door:

5.1. فنگر پرنٽ رسائي

1. پنهنجي رجسٽرڊ آڱر کي فنگر پرنٽ سينسر تي رکو.
2. The lock will verify your fingerprint and unlock if authorized.

5.2. Password Access

1. ان کي چالو ڪرڻ لاءِ ڪي پيڊ کي ڇڪيو.
2. Enter your registered password followed by the '#' key.
3. The lock will verify the password and unlock if authorized.

5.3. Proximity Card Access

1. Place your registered proximity card against the card reader area on the lock.
2. The lock will read the card and unlock if authorized.

5.4. Mechanical Key Access

1. Insert the mechanical key into the keyhole located at the bottom of the handle.
2. Turn the key to unlock the door. This method is primarily for emergency use.

5.5. Auto-Lock Setting

The auto-lock function is disabled by default. To enable or configure it:

1. Press the 'X' button twice to activate the keypad.
2. Enter your master PIN code and press the '✓' button once.
3. Press '7' to enter the auto-lock setting menu.
4. Choose your desired auto-lock delay:
   • Press '1' then '✓' to disable auto-lock.
   • Press '2' then '✓' for 30 seconds delay.
   • Press '3' then '✓' for 60 seconds delay.
   • Press '4' then '✓' for 120 seconds delay.
   • Press '5' then '✓' for 180 seconds delay.

6. سار سنڀال

6.1. بيٽري مٽائڻ

When the batteries are low, the lock will provide an audible or visual alert. Replace all four AA alkaline batteries promptly to ensure continuous operation. Use the emergency 5V port with a power bank if the batteries die completely before replacement.

6.2. صفائي

تالي جي ٻاهرين حصي کي نرم، ڊي سان صاف ڪريوamp ڪپڙو. رگڙيندڙ ڪلينر يا سالوينٽس استعمال ڪرڻ کان پاسو ڪريو جيڪي ختم يا اليڪٽرانڪ حصن کي نقصان پهچائي سگهن ٿا.

7. مسئلا حل ڪرڻ

• لاڪ جواب نه ڏئي رهيو آهي: Check battery levels. If batteries are dead, use the emergency 5V port or mechanical key.
• آڱرين جي نشان جي سڃاڻپ نه ٿي: Ensure your finger is clean and dry. Try re-registering your fingerprint if issues persist.
• پاسورڊ ڪم نه پيو ڪري: Double-check the entered password. Ensure the keypad is active.
• Proximity card not working: Ensure the card is correctly placed against the reader. Try re-registering the card.
• هٿوڙو ڍلو محسوس ٿئي ٿو: Check and tighten all mounting screws. Refer to the installation guide for proper assembly.

8. وارنٽي ڄاڻ

This Phillips Aruma Digital Smart Lock is covered by the manufacturer's standard warranty. Please refer to the warranty card included in your package for specific terms, conditions, and duration. Keep your proof of purchase for any warranty claims.

9. ڪسٽمر سپورٽ

For technical assistance, troubleshooting, or further inquiries, please contact Phillips customer support. Refer to the contact information provided in your product packaging or visit the official Phillips webسپورٽ وسيلن لاء سائيٽ.