هسڪوارنا ايس ٽي 124 212 سي سي 24 انچ ٽو-ايسtagاي برف ڦوڪيندڙ هدايتون دستياب

تعارف

This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your Husqvarna ST124 212cc 24-inch Two-Stagاي برف ڦوڪيندڙ. مھرباني ڪري مشين هلائڻ کان اڳ ھن دستور کي چڱي طرح پڙھو ۽ مستقبل جي حوالي لاءِ ان کي رکو.

شڪل 1: مجموعي طور view of the Husqvarna ST124 212cc 24-inch Two-Stage Snow Blower.

حفاظت جي ڄاڻ

Always prioritize safety when operating the snow blower. Failure to follow safety instructions can result in serious injury or death.

• Read and understand the entire manual before operating the machine.
• ھٿ، پير ۽ ڪپڙا ھلندڙ حصن کان پري رکو.
• Never direct discharge towards people or property.
• Wear appropriate personal protective equipment (PPE), including eye protection and hearing protection.
• ان علائقي کي غير ملڪي شين کان صاف ڪريو جيڪي اوگر ذريعي اڇلائي سگهجن ٿيون.
• Do not operate the machine on steep slopes.
• Turn off the engine and remove the key before performing any maintenance or clearing clogs.
• انجن بند ڪري ۽ ٿڌو ڪري سٺي هوادار علائقي ۾ تيل ڀريو.

سيٽ اپ ۽ اسيمبلي

Your Husqvarna ST124 snow blower requires minimal assembly. Follow these steps to prepare your machine for operation:

1. هينڊ بار اسيمبلي: Attach the lower handlebar section to the main unit using the provided bolts and knobs. Ensure all connections are secure.
2. Upper Handlebar and Control Panel: Secure the upper handlebar section to the lower section. Connect any control cables (drive, auger, chute) to their respective levers on the control panel.
3. چُٽ اسيمبلي: Attach the snow discharge chute to the main unit. Ensure the chute rotator mechanism is correctly aligned and secured.
4. اسڪيڊ جوتا: Adjust the skid shoes to the desired height. For most surfaces, a medium setting is appropriate. For gravel, raise the skid shoes to prevent picking up stones.
5. ٽائر لڳائڻ: If not pre-installed, attach the wheels to the axle using the provided pins. Ensure tires are properly inflated (refer to tire sidewall for pressure).

شڪل 2: پاسي view showing the auger and tire assembly.

آپريٽنگ هدايتون

آپريشن کان اڳ جي چيڪ لسٽ:

• انجڻ جي تيل جي سطح چيڪ ڪريو.
• Fill fuel tank with fresh, unleaded gasoline (refer to engine manual for specific fuel requirements).
• Inspect the area to be cleared for any objects that could be thrown.
• Ensure all controls are functioning correctly.

انجڻ شروع ڪرڻ:

Your Husqvarna ST124 features both a pull start and an electric start for convenience.

1. ٻارڻ والو: ايندھن جي والو کي "آن" پوزيشن ڏانھن ڦيرايو.
2. چوڪس: Move the choke lever to the "FULL CHOKE" position for a cold engine. For a warm engine, use "HALF CHOKE" or no choke.
3. پرائمر بلب: Press the primer bulb 3-5 times (more for very cold conditions) until fuel is visible in the bulb. Do not over-prime.
4. Ignition Key: Insert the ignition key and turn it to the "ON" position.
5. شروع ٿيندڙ:
   • Pull Start: اسٽارٽر هينڊل کي مضبوطيءَ سان پڪڙيو ۽ ان کي تيزي سان ڇڪيو جيستائين انجن شروع نه ٿئي.
   • بجلي جي شروعات: Connect an extension cord to the electric start port and press the electric start button.
6. گرم ٿيو: Once the engine starts, gradually move the choke lever to the "RUN" position as the engine warms up (typically 30-60 seconds).

Figure 3: Close-up of the engine, fuel valve, primer bulb, and electric start port.

سنو بلور کي هلائڻ:

The control panel provides easy access to all operational functions.

شڪل 4: مٿي view of the control panel with speed and chute controls.

• ڊرائيو ڪنٽرول: Engage the drive lever to move the snow blower forward or backward. Use the speed selector to choose from multiple forward and reverse speeds.
• Auger Control: Engage the auger lever to activate the auger blades for snow clearing.
• Chute Control: Use the chute rotation lever to adjust the direction of snow discharge (180-degree rotation). Use the chute deflector lever to adjust the height and distance of the snow stream.
• هيڊ لائٽ: Activate the LED headlight for improved visibility in low-light conditions.

سار سنڀال

باقاعده سار سنڀال توهان جي برف ڦوڪيندڙ جي ڊگهي عمر ۽ بهترين ڪارڪردگي کي يقيني بڻائي ٿي.

• انجڻ جو تيل: هر استعمال کان اڳ تيل جي سطح چيڪ ڪريو. آپريشن جي پهرين 5 ڪلاڪن کان پوءِ تيل تبديل ڪريو، پوءِ هر 25 ڪلاڪن يا سال ۾ هڪ ڀيرو.
• اسپارڪ پلگ: اسپارڪ پلگ کي هر سال معائنو ڪريو ۽ صاف ڪريو. جيڪڏهن اهو خراب يا گندو آهي ته ان کي تبديل ڪريو.
• ٻارڻ جو نظام: Use a fuel stabilizer if storing the machine for extended periods. Drain the fuel tank at the end of the season if not using stabilizer.
• Auger Blades & Scraper Bar: Inspect for wear and damage. Replace worn parts to maintain clearing efficiency.
• ڪٽڻ جا پن: Always keep spare shear pins on hand. These are designed to break to protect the gearbox from damage if the auger hits an obstruction.
• عام صفائي: Clean the machine after each use, removing snow and debris.

مشڪلاتون

وڌيڪ پيچيده مسئلن لاءِ، هڪ قابل سروس ٽيڪنيشن سان صلاح ڪريو.

وضاحتون

وارنٽي ۽ سپورٽ

For detailed warranty information, please refer to the warranty card included with your product or visit the official Husqvarna website. For technical support, replacement parts, or service inquiries, please contact Husqvarna customer service or an authorized service dealer.

توهان وڌيڪ معلومات ۽ مدد تي ڳولي سگهو ٿا Husqvarna Store on Amazon.