تعارف
This manual provides detailed instructions for the installation, operation, and maintenance of your PNI AGD1200 Garage Door Opener Automation Kit. Please read this manual thoroughly before beginning installation or operation to ensure safe and correct use of the product. This kit is designed for automating sectional garage doors up to 17 square meters.
پيڪيج مواد
پڪ ڪريو ته هيٺ ڏنل سڀئي جزا توهان جي پيڪيج ۾ موجود آهن:
- موٽر يونٽ
- ريموٽ ڪنٽرول (2 يونٽ)
- Rail Sections (3 x 110 cm)
- Rail Connection Pieces (2 units)
- چڙهڻ جو سامان
- استعمال ڪندڙ جو دستياب (ھي دستاويز)
Image: Included mounting accessories for installation.
Image: Rail sections and chain mechanism.
حفاظت جي ڄاڻ
پيداوار ۽ ملڪيت کي نقصان يا نقصان کان بچڻ لاءِ هميشه هيٺ ڏنل حفاظتي احتياطن تي عمل ڪريو:
- انسٽاليشن ۽ استعمال ڪرڻ کان پهريان سڀ هدايتون احتياط سان پڙهو.
- Ensure the garage door is balanced and in good working condition before installing the opener.
- Disconnect power to the garage door opener before performing any maintenance or repairs.
- ٻارن ۽ پالتو جانورن کي گيراج جي دروازي واري علائقي کان پري رکو، خاص ڪري آپريشن دوران.
- Do not allow children to play with the remote controls.
- Install the wall control button at least 1.5 meters (5 feet) above the floor and away from all moving parts of the door.
- Never walk or stand under a moving garage door.
- Ensure the safety reversal system is tested monthly.
- صرف اصل اسپيئر پارٽس ۽ لوازمات استعمال ڪريو.
وضاحتون
| خاصيت | تفصيل |
|---|---|
| پراڊڪٽ ڪوڊ | PNI-AGD1200 |
| پاور سپلائي Voltage | 230 V AC 50/60 Hz |
| Motor Force (Closing/Opening) | 1200 اين |
| ريموٽ ڪنٽرول فريڪئنسي | 433 MHz |
| ريموٽ ڪنٽرول پاور | 27A 12V بيٽري |
| Signal Encoding | متحرڪ ڪوڊ |
| LED لائيٽ | 3 V 0.045 W |
| LED Illumination Duration | 3 منٽ |
| آپريٽنگ جي درجه حرارت | -26 ~ 80 °C |
| Product Dimensions (Motor Unit) | 21 x 11 x 37 سينٽي |
| پيداوار جو وزن | 13.7 ڪلو |
| مواد | ڌاتو |
| Recommended Door Type | Sectional Garage Doors up to 17m² |
سيٽ اپ ۽ تنصيب
قبل از انسٽاليشن چيڪ
- Ensure the garage door operates smoothly manually and is properly balanced.
- دروازي جي رستي ۾ ڪنهن به رڪاوٽ جي جانچ ڪريو.
- Verify that the power outlet is within reach and meets the specified voltage گهرجون.
Assembling the Rail
- Connect the three rail sections using the provided rail connection pieces. Ensure the chain is correctly threaded through the entire rail assembly.
- Secure all connections firmly with the appropriate hardware.
Image: Rail mounting brackets.
موٽر يونٽ لڳائڻ
- Attach the assembled rail to the motor unit.
- Position the motor unit centrally above the garage door, ensuring it is level.
- Secure the motor unit to the ceiling joists or a sturdy mounting board using the provided mounting accessories.
- Connect the other end of the rail to the garage door header bracket.
تصوير: سامهون view موٽر يونٽ جي.
Image: Motor unit with rail and power cable.
تصوير: هيٺيون view of the motor unit, showing mounting points.
بجليءَ جو رابطو
Once the motor unit and rail are securely mounted, plug the power cord into a grounded 230V AC outlet. Ensure the power cord is routed safely and not pinched by any moving parts.
آپريٽنگ هدايتون
ريموٽ ڪنٽرول جوڙڻ
- Press and hold the 'CODE' button on the motor unit's control panel until the LED display shows 'P'.
- Within 30 seconds, press the desired button on your remote control. The LED display will flash to confirm successful pairing.
- Repeat for any additional remote controls.
Image: Motor unit with two remote controls.
Image: Remote control for the garage door opener.
بنيادي آپريشن
- کليل دروازو: Press the programmed button on the remote control or the 'UP' button on the control panel.
- دروازو بند ڪريو: Press the programmed button on the remote control or the 'DOWN' button on the control panel.
- Stop Door: Press any button on the remote control or the 'SET' button on the control panel while the door is in motion.
حدن کي ترتيب ڏيڻ
The opener automatically learns the door's travel limits during initial setup. If adjustments are needed:
- Press and hold the 'SET' button until the LED display shows '1' for the open limit or '2' for the close limit.
- Use the 'UP' and 'DOWN' buttons to move the door to the desired open or close position.
- Press 'SET' again to confirm the new limit.
سار سنڀال
Regular maintenance ensures optimal performance and longevity of your garage door opener:
- مهيني: Test the safety reversal system. Place a 2x4 inch board flat on the floor in the door's path. The door should reverse upon contact. If it does not, adjust the force settings or consult a technician.
- ٽه ماهي: Lubricate the door's moving parts (rollers, hinges, bearings) with a garage door lubricant. Do not lubricate the rail or chain unless specifically instructed.
- سالانه: Inspect all hardware for loose bolts, worn parts, or signs of damage. Tighten any loose fasteners.
- Keep the motor unit and rail clean from dust and debris.
مشڪلاتون
عام مسئلن ۽ انهن جي امڪاني حلن لاءِ هيٺ ڏنل جدول جو حوالو ڏيو:
| مسئلو | ممڪن سبب | حل |
|---|---|---|
| اوپنر ريموٽ ڪنٽرول جو جواب نٿو ڏئي. | Remote battery is dead; remote is not paired; signal interference. | Replace remote battery; re-pair remote control; check for sources of interference. |
| Door does not open or close completely. | Travel limits need adjustment; obstruction in door path. | Adjust travel limits as per instructions; remove any obstructions. |
| دروازو غير متوقع طور تي الٽي ٿو. | Safety reversal system activated by obstruction; force settings too high/low. | Check for obstructions; test safety reversal system; adjust force settings if necessary (consult manual for specific steps). |
| Motor runs but door does not move. | Trolley disengaged from door; chain/belt broken or loose. | Re-engage trolley; inspect chain/belt for damage or tension. |
| ايل اي ڊي لائيٽ نه ٿي جلي. | LED bulb faulty; power issue. | بجلي ڪنيڪشن چيڪ ڪريو؛ جيڪڏهن مسئلو برقرار رهي، ته سپورٽ سان رابطو ڪريو. |
وارنٽي ۽ سپورٽ
Your PNI AGD1200 Garage Door Opener Automation Kit is covered by a manufacturer's warranty against defects in materials and workmanship. Please retain your proof of purchase for warranty claims.
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact PNI customer support through their official website or the retailer where the product was purchased. Provide your model number (AGD1200) and a detailed description of the issue when seeking support.
