DIGITEN گيس فائر پلیس ريموٽ ڪنٽرول ڪٽ WTC401 يوزر مينوئل

1. تعارف

This manual provides detailed instructions for the installation, operation, and maintenance of your DIGITEN Gas Fireplace Remote Control Kit, Model WTC401. This kit is designed to provide wireless control for millivolt valve gas fireplaces, offering ON/OFF, automatic thermostat, and timer functions for enhanced convenience and comfort.

2. حفاظت جي ڄاڻ

Please read all safety warnings and instructions carefully before installation and operation to prevent injury or property damage.

• جلدtage حد: Do not use this remote-control system on applications with voltages مٿي 24 وولٽ AC/DC ۽ 1 amp current. Exceeding these limits can damage the unit and pose a safety hazard.
• گرمي جي نمائش: The receiver unit must be installed away from high heat sources (above 130°F / 54°C) to ensure proper function and prevent damage.
• دستي بند: For extended absences from home, it is recommended to manually turn off the fireplace at the gas valve for maximum safety.
• پيشه ورانه تنصيب: If you are unsure about any part of the installation process, consult a qualified technician.
• بيٽري جي حفاظت: Always use the specified battery types and ensure correct polarity. Do not mix old and new batteries or different battery types. Dispose of used batteries responsibly.

3. پيڪيج مواد

تصديق ڪريو ته هيٺ ڏنل سڀئي جزا توهان جي پيڪيج ۾ شامل آهن:

Figure 3.1: Contents of the DIGITEN Gas Fireplace Remote Control Kit.

• ريموٽ ڪنٽرول (ٽرانسميٽر)
• وصول ڪندڙ باڪس
• Wall Plate for Receiver
• ڪنيڪشن تار
• چڙهڻ اسڪرو

4. پراڊڪٽ ختمview

4.1 Remote Control (Transmitter)

The remote control features a large, backlit LCD screen for clear display of current room temperature, desired set temperature, operating mode, and timer status. It operates wirelessly with a signal range of up to 65 feet (20 meters).

Figure 4.1: Remote Control LCD Display and Button Functions.

• LCD ڊسپلي: Shows current room temperature, set temperature, temperature unit (°F/°C), timer, safety lock status, and battery low indicator.
• موڊ بٽڻ: Cycles through ON, AUTO, and OFF operating modes.
• ٽائمر بٽڻ: Activates and adjusts the timer function.
• مٿي/هيٺ تير: Adjusts set temperature and timer values.
• اندروني سينسر: The remote control contains the temperature sensor for thermostat operation.

4.2 وصول ڪندڙ

The receiver unit acts as a wireless switch for your fireplace. It connects directly to the millivolt valve and receives commands from the remote control. It features a manual ON/AUTO/OFF switch and a 'LEARN' button for pairing.

Figure 4.2: Receiver Box and Wall Plate.

• ON/AUTO/OFF Switch: Allows manual control of the fireplace directly from the receiver.
• سکو بٽڻ: Used to establish communication between the remote and receiver.
• بيٽري جو خانو: Houses 4 AA batteries for power.

5. سيٽ اپ ۽ تنصيب

5.1 بيٽري لڳائڻ

Batteries are not included in the kit and must be purchased separately.

Figure 5.1: Battery requirements for the remote and receiver.

• ريموٽ ڪنٽرول: Requires 2 AAA batteries. Open the battery compartment on the back of the remote and insert the batteries, observing correct polarity.
• وصول ڪندڙ: Requires 4 AA batteries. Open the battery compartment on the receiver box and insert the batteries, observing correct polarity.

5.2 Receiver Wiring to Millivolt Valve

This system is designed for millivolt gas valve systems. It functions as an on/off switch and connects to the TH and TH/TP terminals of your millivolt valve.

Figure 5.2: Connecting the receiver to the millivolt gas valve.

1. Ensure the gas supply to the fireplace is turned off before beginning installation.
2. Locate the millivolt valve on your gas fireplace. Identify the TH and TH/TP terminals.
3. Connect the two wires from the receiver to the TH and TH/TP terminals of the millivolt valve. The connection is non-polarized, so the order of the wires does not matter.
4. Mount the receiver box in a suitable location, either inside the fireplace control area or on a wall using the provided wall plate and screws. Ensure it is away from direct heat.
5. Restore the gas supply to the fireplace.

Figure 5.3: Millivolt Gas Valve Terminals.

5.3 Pairing the Remote and Receiver

After installing batteries and wiring the receiver, you need to pair the remote control with the receiver.

1. On the receiver unit, slide the switch to the 'ON' or 'AUTO' position.
2. Press and hold the 'LEARN' button on the receiver until you hear a beep or see an indicator light flash (refer to receiver for specific indicator).
3. Within 10 seconds, press any button on the remote control. The receiver will beep again or the light will stop flashing, indicating successful pairing.
4. Test the connection by pressing the ON/OFF buttons on the remote. The fireplace should respond.

6. آپريٽنگ هدايتون

6.1 پاور آن/آف

• چالو ڪرڻ لاء: Press the 'MODE' button on the remote until 'ON' is displayed, or press the 'Up' arrow button.
• بند ڪرڻ: Press the 'MODE' button on the remote until 'OFF' is displayed, or press the 'Down' arrow button.

6.2 موڊ جي چونڊ

Press the 'MODE' button on the remote to cycle through the following operating modes:

• آن موڊ: The fireplace will remain continuously on until manually turned off.
• بند موڊ: The fireplace will remain continuously off.
• AUTO Mode (Thermostat): The fireplace will turn on and off automatically to maintain the desired set temperature. The remote's built-in sensor measures the room temperature.

6.3 Thermostat Function (AUTO Mode)

Figure 6.1: The remote control houses the temperature sensor.

• In AUTO mode, use the 'Up' and 'Down' arrow buttons to set your desired temperature. The remote will display both the current room temperature and the set temperature.
• To switch between Fahrenheit (°F) and Celsius (°C), refer to the remote control's specific instructions (usually a combination button press or a switch in the battery compartment).
• The fireplace will activate when the room temperature drops below the set temperature and deactivate when it reaches or exceeds the set temperature.

6.4 ٽائمر فنڪشن

• ٽائمر کي چالو ڪرڻ لاءِ 'ٽائمر' بٽڻ دٻايو.
• Use the 'Up' and 'Down' arrow buttons to set the desired duration for the fireplace to operate (e.g., 30 minutes, 1 hour).
• The fireplace will automatically turn off once the set time has elapsed.

6.5 چائلڊ سيفٽي لاڪ

The child safety lock prevents accidental activation of the fireplace.

Figure 6.2: Activating the Child Safety Lock.

• بند ڪرڻ: Press and hold the 'Up' arrow button and the 'TIMER' button simultaneously for a few seconds until a lock icon appears on the LCD screen.
• کولڻ لاءِ: Press and hold the 'Up' arrow button and the 'TIMER' button simultaneously again until the lock icon disappears.

7. سار سنڀال

7.1 بيٽري مٽائڻ

When the battery low indicator appears on the remote control's LCD screen, replace the batteries within two weeks to ensure continuous operation.

• ريموٽ ڪنٽرول: 2 نئين AAA بيٽرين سان تبديل ڪريو.
• وصول ڪندڙ: 4 نئين AA بيٽرين سان تبديل ڪريو.
• Always use fresh, high-quality alkaline batteries.

8. مسئلا حل ڪرڻ

9. وضاحتون

شڪل 9.1: پيداوار جا طول و عرض.

10. وارنٽي ۽ سپورٽ

DIGITEN provides a one-year warranty for any product quality problems. If you encounter any issues or require assistance, please contact DIGITEN customer support through the retailer where the product was purchased or visit the official DIGITEN webسپورٽ رابطي جي معلومات لاء سائيٽ.

We are committed to providing reliable products and personalized service to ensure your satisfaction.