Current CTRL042 Outdoor Wireless Control System Installation Guide

Current CTRL042 Outdoor Wireless Control System

 انسٽاليشن کان اڳ

• Carefully unpack the Light Grid Node. Inspect for defects before installing.
• Check electrical parameters. Ensure that the luminaire operating power is below 1000W, and its operating voltage is within 120 to 277 V AC
• Using the Light Grid Node outside its operating parameters will void its warranty.
• Validate Fixture Approval with Current. Prior to integrating the Internal Node in any luminaire, Current strongly recommends validation testing of the design to ensure Light Grid performance.

وائرنگ نوڊ کي فڪسچر ۾

 گهربل سامان

• Light Grid Internal Node
• لومينئير
• Two #10 mounting screws of appropriate type and length (recommended)

Following the Wiring Diagram, perform the following steps:

• نوڊ جي L-In (ڪارو) کي فڪسچر جي لائن (ڪارو) سان ڳنڍيو.
• Connect L-Out (Red) of the node to AC Line input of the driver.
• Connect the neutral (white) of the node to the neutral (white) of the fixture.
• Connect the neutral (white) of the LED Driver/HID Ballast to the neutral (white) of the fixture.

For dimmable fixture, please perform the following extra steps:

• Connect the Dim- (grey or pink) of the node to the negative dimming wire of the LED Driver/HID Ballast.
• نوڊ جي Dim + (وائلٽ) کي LED ڊرائيور/HID بالسٽ جي مثبت ڊمنگ تار سان ڳنڍيو.

وائرنگ تصوير

خبردار

• RISK OF DAMAGE ON NODE
• نوڊ يا فيڪٽر تي نقصان جو خطرو جيڪڏهن سڀني وائرنگ جي هدايتن جو احترام نه ڪيو وڃي.

وائرنگ سيٽ اپ

• سڀني وائرنگ سيٽ اپ کي NFPA70 جي مطابق ڪرڻ گهرجي: نيشنل اليڪٽرڪ ڪوڊ ۽ CSA-22.
• Maximum temperature around the internal node: 70°C

نوڊ جي جڳھ ۽ تنصيب

• The location of the node inside the Luminaire must be selected to keep the node as far away as possible from sources of heat or electrical electrical interferences sources, such as the lamp ballast/driver/power supply, or the light bulb or LED panel and its heatsink. Never install the node directly above these; The preferred location is in the lower part of the Luminaire below any source of heat.
  Record the location the Internal Node is installed (since it doesn’t have GPS), this can be done by either manually recording it or using the Current Commissioning Light Grid App that is available on iOS to ensure the node is positioned in current location on the map view.
• پڪ ڪريو ته نوڊ جي جڳھ کي 2 مناسب پوزيشن واري اسڪرو سوراخ جي جڳهن سان گڏ محفوظ ۽ مضبوط چڙهندڙ سپورٽ سطح مهيا ڪري ٿي.
• Attach the node into the fixture using 2 screws.

اهم نوٽس: 

• All unused wires must be terminated with an appropriate UL CSA approved Wire Nut.
• نوڊ هائوسنگ کي کولڻ يا نوڊ جي ڪنهن به حصي کي تبديل ڪرڻ جي ڪوشش نه ڪريو.
• It is the integrator’s responsibility to ensure the temperature rating of the Light Grid node is never exceeded; Make certain that the ambient temperature around the node in its selected location can never exceed the maximum operating temperature (+70°C).
• The node by default will turn the luminaire ON until schedule is downloaded to the node from the CMS software.

Antenna Location & Installation

• To select the optimum antenna mounting point, read the following and refer to the illustrations (below) showing examples of the best, acceptable and unacceptable locations and orientations.
• The antenna must be mounted on a conductive (metal) surface. If the surface is made of non-conductive material (such as plastic), the inner surface where the antenna is to be installed should be lined with a thin metal sheet or foil tape (copper) approximately 6” to 12” diameter, with the antenna installed through the center of this me
• The antenna is to be installed through a 12mm diameter hole drilled through mounting surface.
• The mounting surface around this hole must be perfectly smooth, flat, and free of any burrs to insure a watertight seal.
• اينٽينا جي مٿاڇري جي ٿلهي 1mm کان 6mm جي ٿلهي ان نقطي تي هجڻ گهرجي جتي سوراخ ڪيو وڃي.

LightGrid Internal Node 2.x Series Installation Guide

• A suitable location for both the node and antenna must be found which allows the antenna and its wire to be routed from the node installation point, to where it can be passed through the antenna mounting hole from the inside of the fixture.
• The antenna must be installed vertically with respect to the ground. Therefore, the surface it is mounted to must be horizontal.
• If the most suitable location is not perfectly horizontal at the point where the antenna is mounted, bevel washers may be used on either side of the mounting hole to insure the antenna will be perfectly vertical when installed.
• فڪسچر جي ٻاهران اينٽينا جي چونڊيل جڳهه افقي طور تي ڪنهن به اهم موڙيندڙ (ڌاتو) رڪاوٽ کان پاڪ هجڻ گهرجي، ان جي چوڌاري 360 درجا، انٽينا جي بنياد کان ماپي وڃي جتي اهو ايل سان ملندو آهي.amp fixture surface, to at least 12” (30 cm) above this surface. Plastic or glass features will not affect the antenna if they are at least 0.5 to 1” or 1-2cm away from it.
• فڪسچر تي اينٽينا لاءِ ترجيح واري جڳھ عام طور تي فڪسچر جي مٿئين مٿاڇري تي سڀ کان مٿاھين پوائنٽ آھي، ھن مٿاڇري تي مرڪز آھي.
• On hanging fixtures supported from above, the antenna may be mounted pointing downward, at a suitable location on the lower surface of the fixture housing.
• When installing the antenna, make sure installing the supplied O- ring and be very careful not to overtighten the M12 plastic screw and the antenna.
• Steps for the Antenna installation:
• Install O-ring on the lower flange of the SMA connector assembly (near the wire).
• Route the Antenna SMA connector assembly from the inside of the fixture to the antenna’s exit point.
• Fit the threaded portion of the SMA connector assembly through the 12 mm hole. Be careful not damaging the threads in the process.
• Install the serrated lock nut then screw the M12 plastic nut and tighten to a snug fit. To avoid risk of damages during transport, the antenna should be installed on the SMA connector only once the luminaire installation on site is completed.
• Screw the antenna on the SMA connector to a hand-tight to a snug fit. Do not over tighten.

ليبلز

• The Internal Node is supplied with 3 identical nameplate labels. One label is affixed on the node housing. The other two labels packaged with each node are to be affixed on a visible location on the exterior of the fixture and/or the base of the pole, for commissioning purposes.
• The MAC address of each internal Light Grid node is printed on the label both as barcode & plain text.

تصديق جي جاچ

• Non-Dimmable Fixture: To verify the installation of Light grid Internal Node, please follow these steps:
• Apply power to the fixture (120- 277V AC, 50/60 Hz)
• If the installation has been done correctly, the light will turn OFF briefly during the first 60 seconds after power is applied.
• Dimmable Fixture: To verify the installation of Lightgrid Internal Node, please follow these steps:
• Apply power to the fixture (120- 277V AC, 50/60 Hz)
• If the installation has been done correctly, the light output will visibly dim within the first 60 seconds after power is applied and then return to full brightness.

ايف سي سي جو بيان

FCC بيان:
نوٽ: هي سامان آزمايو ويو آهي ۽ FCC ضابطن جي حصو 15 جي مطابق، ڪلاس A ڊجيٽل ڊوائيس جي حدن جي تعميل لاءِ مليو آهي. اهي حدون ٺهيل آهن ته نقصانڪار مداخلت جي خلاف مناسب تحفظ مهيا ڪن جڏهن سامان تجارتي ماحول ۾ هلندي آهي. هي سامان پيدا ڪري ٿو، استعمال ڪري ٿو، ۽ ريڊيو فریکوئنسي توانائي کي ريڊيٽ ڪري سگهي ٿو، ۽، جيڪڏهن نصب نه ڪيو وڃي ۽ هدايت واري دستور مطابق استعمال ڪيو وڃي، ريڊيو ڪميونيڪيشن ۾ نقصانڪار مداخلت جو سبب بڻجي سگهي ٿو. رهائشي علائقي ۾ هن سامان جو آپريشن نقصانڪار مداخلت جو امڪان آهي، ان صورت ۾ صارف کي پنهنجي خرچ تي مداخلت کي درست ڪرڻ جي ضرورت پوندي.

ايف سي سي تابڪاري جي نمائش جو بيان:

• ھي سامان FCC تابڪاريءَ جي نمائش جي حدن سان لاو ٿئي ٿو جيڪو اڻ ڪنٽرول ماحول لاءِ مقرر ڪيو ويو آھي. ھي سامان انسٽال ڪيو و andي ۽ ھليو و aي گھٽ ۾ گھٽ فاصلي سان 20 سينٽي ميٽر ريڊي ايٽر ۽ توھان جي جسم جي وچ ۾.
• ڪا به تبديلي يا ترميم واضح طور تي منظور نه ڪئي وئي پارٽي طرفان تعميل جي ذميواري هن سامان کي هلائڻ لاءِ صارف جي اختيار کي رد ڪري سگهي ٿي.

CAN ICES (A)/NMB (A):
ھن ڊيوائس ۾ لائسنس-مستثنيٰ ٽرانسميٽر/رسيور آھن جيڪي انوويشن، سائنس ۽ اڪنامڪ ڊولپمينٽ ڪئناڊا جي لائسنس-ڇڏيل RSS(ن) جي تعميل ڪن ٿا. آپريشن هيٺ ڏنل ٻن شرطن جي تابع آهي:

1. هي ڊوائيس مداخلت جو سبب نه ٿي سگھي.
2. هن ڊوائيس کي ڪنهن به مداخلت کي قبول ڪرڻ گهرجي، جنهن ۾ مداخلت شامل آهي جيڪا ڊوائيس جي ناپسنديده آپريشن سبب ٿي سگهي ٿي.