مواد لڪائڻ
1 Digilog ESP32 Super Mini Dev Board
2 وضاحتون
3 سيٽ اپ-1
4 سيٽ اپ-1
5 سيٽ اپ-2
6 دستاويز / وسيلا
6.1 حوالو

Digilog-logo

Digilog ESP32 Super Mini Dev Board

Digilog-ESP32-Super-Mini-Dev-Board-product

وضاحتون

  • Product Name: ESP32 Super Mini Dev Board
  • Board Type: ESP32C3 Dev Module
  • Communication: USB CDC
  • باڊ جي شرح: 9600
  • Onboard LED: GPIO8

سيٽ اپ-1

My ESP32 Super Mini Dev Board (Fig. 1) accepts sketches from a PC, but it does not communicate with the Serial Monitor (Bd = 9600) though the onBoard LED (at GPIO8) blinks.
[image|403×203](upload://pRi2u3tDsAxTivzokiEplEtzhlC.jpeg)
تصوير-1

Digilog-ESP32-Super-Mini-Dev-Board-fig-1

سيٽ اپ-1

  • Board: “ESP32C3 Dev Module”
  • USB CDC on Boot: “Enabled”
  • Port: “COM13 (ESP32S3 Dev Module)” //no other option

خاڪو

  • define LED_BUILTIN 8
  • char myData[10];
  • خالي سيٽ اپ ()
  • Serial.begin(9600);
  • pinMode(LED_BUILTIN, OUTPUT)
  • خالي لوپ ()
  • digitalWrite(LED_BUILTIN, HIGH); // turn the LED on (HIGH is the voltagاي سطح)
  • delay(1000); // wait for a second
  • digitalWrite(LED_BUILTIN, LOW); // turn the LED off by making the voltage LOW delay(1000)
  • byte n = Serial.available();
  • if (n != 0) { byte m = Serial.readBytesUntil(‘\n’, myData, sizeof (myData)-1); myData[m] = ‘\0’
  • Serial.println(myData); }
  • Serial.println(“Hello”); }

The following setup has solved the problem.

سيٽ اپ-2

  • Board: “LOLIN C3 Mini”
  • USB CDC on Boot: “Enabled”
  • Port: “COM13 (ESP32S3 Dev Module)”
  • Bd = 9600

ٻاھر

  • سلام
  • سلام
  • Arduino //From InputBox of SM to ESP32C3 to OutputBox of SM
  • سلام
  • سلام

Would be glad to hear your opinion as to — “what is LOLIN C3”.

  1. Do not place the ESP32C3 Super Mini Board on the Breadboard to avoid contact problems.
  2. The onboard LED is connected at DPin-8.
  3. Use a male-female jumper and connect the female side at DPin-9 to act as an external switch/button.
  4. The connection diagram of the onFig. 1 LED and a button are similar to Fig. 1.Digilog-ESP32-Super-Mini-Dev-Board-fig-2
  5. Select Board as follows: IDE 2.3.1 –> Tools –> ESP32.
  6.  LOLIN C3 Mini USB CDC On Boot: Enabled.
  7. Upload the provided sketch to the board.
  8. Check that the onboard LED is off initially.Digilog-ESP32-Super-Mini-Dev-Board-fig-3
  9. Closing the switch will make the onboard LED start blinking at a 2-second interval.
  10. Ensure that the onboard LED is on.f
  11. Gently touch the male side of the hanging wire/jumper with h G-pin of the Mini Board.
  12. Confirm that the onboard LED is blinking at a 2-second interval.
  13. Press the RST (Reset) Button of the Mini Board and repeat the process if needed.

دستاويز / وسيلا

Digilog ESP32 Super Mini Dev Board [pdf] هدايتون
ESP32 Super Mini Dev Board, ESP32, Super Mini Dev Board, Mini Dev Board, Board

حوالو

تبصرو ڇڏي ڏيو

توهان جو اي ميل پتو شايع نه ڪيو ويندو. گهربل فيلڊ نشان لڳل آهن *